Radical Scientific Equipments Private Limited

Inner Chamber, outer chamber & support ring are fully made of stainless steel.

Heaters cover stand & carrier/bucket are made of stainless steel.

Lid made of thick machined stainless steel plate.

Brass knobs ensures user safety & safe locking.

Lid is fitted with pressure gauge, spring loaded safety valve, double safety valve, manual exhaust valve, vacuum beaker as safety device & water level indicator.

Drain Valve facilities easy cleaning of the chamber.

Molded joint less silicon rubber gasket.

All internal joints are argon arc welded, ground & polished to give crevice free internals.

Miniature circuit breaker for mains on/off plus safety of control panel.

Industrial grade energy efficient heaters reduce power bill drastically.

Technical Specifications:

      Sterilizing pressure: 1.2kgf/cm2 (15 psi) at 121°C

      Operating pressure: from 15 to 22 psi (adjustable)

Constant Temperature Water Bath RSTI-137

Thermostatically controlled. Double walled construction. Complete with stirrer. Temperature range upto 100 DegreeC. Workable on 220V AC 50Hz single phase.

Inner Chamber Sizes are available

• 425x250x225 mm
• 425x375x375 mm
• 650x450x450 mm

Optional

• Microprocessor PID digital temp. Indicator cum controller.
• Auto cut off device when water level is low.

Water Bath - Tissue Flotation RSTI-138 Series
Double walled round construction. Inner chamber stainless steel/black anodized aluminum and outer made out of mild steel painted in epoxy powder coating. Thermostatic control, temperature range from ambient to 80 DegreeC. Complete with indicators, wire & plug. To work on 220V AC.

Inner Chamber Sizes are available

• 200x75 mm
• 250x175 mm

Water Bath Incubator Shaker RSTI-140 Series
Similar to other water bath but fitted with inbuilt shaker for different experiments demanding shaking at constant speed under controlled temperature conditions. The temp. Is controlled by capillary type thermostat from ambient to 100 DegreeC.

RPM range - 40-140 with variable electronic speed regulator workable on 220V AC 50 Hz Single Phase.

Inner Chamber Sizes are available

• 275x275x150 mm
• 405x300x150 mm

Optional

• Microprocessor PID digital temp. Indicator cum controller.
• Digital RPM meter
• Auto cut off device when water level is low.

Additional Information:

• Production Capacity: 20 days

Constant Temperature Refrigerated Liquid Bath RSTI-141:
Outer body is made of thick mild steel duly powder coated painted and inner chamber is made up of 304 grade stainless steel. Lid is also double walled properly insulated and is with locking facility. Whole unit is mounted on sturdy angle iron frame the cooling coils are brazes to the outer side of S.S. chamber thus ensuring perfect and uniform cooling. Insulation is done with thick glass wool to prevent any temp. loss. For attaining the temp. below ambient, the refrigeration is done through CFC free hermetically sealed compressor and & for attaining the temp. above ambient, heating is done with immersion type heating element. Constant Temperature Refrigerated Liquid Bath RSTI-141 Series Fitted with stirrer for temperature uniformity throughout the chamber. Temperatures range is from 5 DegreeC to 90 DegreeC is controlled by dual Display Microprocessor PID Digital Temperature Indicator cum Controller with a accuracy of +0.5 DegreeC digital temp. To work on 220/230volts AC supply. The unit is also fitted with a FHP PUMP for circulating the cooled liquid to an external source such as condenser coils, etc.

Sahli Hemoglobin Meter(HSN- 9027)

Comparator Holder: 1 No.

Square H.B. Tube: 2 Nos.

H.B. Pipette: 1 No.

Amber colored glass bottle: 1No.

Glass Stirrer: 1 No.

Dropper with teat: 1No.

Cleaning Brush: 1No.

Spare latex tubing one meter: 1 No

Comparator Holder: 1 No.

Square H.B. Tube: 2 Nos.

H.B. Pipette: 1 No.

Amber colored glass bottle: 1No.

Glass Stirrer: 1 No.

Dropper with teat: 1No.

Cleaning Brush: 1No.

Spare latex tubing one meter: 1 No

Additional Information:

• Production Capacity: 50
• Delivery Time: READY STOCK
• Packaging Details: CARD BOARD BOX

Water Bath - Rectangular RSTI-136 Series (Single walled)
It is a single walled unit inner chamber made up of S.S. Wall construction and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses.

Concentric rings can be removed to accommodate containers of various sizes. Temperature from ambient to 100 DegreeC is controlled by Hydraulic capillary type thermostat with accuracy of + 1 Degree C . Workable on 220V AC 50Hz Single Phase.

Inner Chamber Size are available Holes Cap. (Aprox.)

• 300x250x100 mm 6 Holes of 75mm 8L
• 355x405x100 mm 12 Holes of 75mm 15L

Tissue Floatation Bath RSTI-3D Series
Tissue Floatation Bath has been developed using microprocessor controls and a modular design that has improved reliability and precision. Corrosion resistant material for durability. Tissue Floatation Bath RSTI-3D Series Temperature settings are controlled by feature touch buttons for accurate and precise control and the easy to read LED display show both, set temperature and actual temperature. The probe has a thermostat sensor inside that turns off when it is lifted up and re-starts when placed back in the basin.

Water Bath - Recangular RSTI-135 Series (Double walled)
It is a double walled unit inner chamber made up of S.S. Sheet and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses.

Concentric rings can be removed to accommodate containers of various sizes. Temperature from ambient to 100 DegreeC is controlled by Hydraulic capillary type thermostat with accuracy of + 1 Degree C. Workable on 220V AC 50Hz Single Phase. Water Bath Recangular RSTI-135 Series.

Inner Chamber Sizes are available Holes Cap. (Aprox.)

• 300x250x100 mm 6 Holes of 75mm 8L
• 355x405x100 mm 12 Holes of 75mm 15L

Optional

• Microprocessor PID digital temp. Indicator cum controller.
• Auto cut off device when water level is low.

Standard Double Wall Fabrication, inner chamber made of richly anodized aluminum or highly polished stainless steel sheet. Exterior fabricated out of thick mild steel duly finished with white powder coating. The gap between the walls is fitted with special grade glass wool. Provided with two or three removable shelves.
Kanthal wire heating elements provided on three sides attain quick and uniform heating in range of 50 DegreeC to 250 DegreeC +2-3 DegreeC controlled by hydraulic type capillary thermostat.
An L- Shaped prismatic thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.

Size are available-

• 300x300x300 mm
• 350x350x350 mm
• 400x400x400 mm
• 450x450x450 mm
• 600x450x450 mm
• 600x600x600 mm
• 900x600x450 mm
• 900x600x600 mm
• 900x900x900 mm

Optional

• Air circulating fan
• Timer 0-99 hours

Sizes are available

• 300x300x300 mm
• 350x350x350 mm
• 400x400x400 mm
• 450x450x450 mm
• 600x450x450 mm
• 600x600x600 mm
• 900x600x450 mm
• 900x600x600 mm
• 900x900x900 mm

Optional

• Timer 0-99 hours

Triple wall fabrication, inner chamber made of mild steel or highly polished stainless steel sheet. Exterior fabricated out of thick mild steel duly finished with white powder coating or other color combinations. The gap between the walls is fitted with special grade glass wool for heat insulation. Provided with two or three removable shelves. Special elegant door closing device has been provided. Temperature range upto 300 DegreeC is controlled by Dual display microprocessor PID digital temperature indicator cum controller & one air circulation fan.

Control panel is provided with selector switch of high or low rates of power, Temperature controller and indicators for mains and heat. Supplied with plug and chord. Equipment suitable to be working on 220V AC 50Hz single phase.

Sizes are available

• 300x300x300 mm
• 350x350x350 mm
• 400x400x400 mm
• 450x450x450 mm
• 600x450x450 mm
• 600x600x600 mm

Drying Oven - Industrial RSTI-104 Series
Standard Double Wall Fabrication, inner & outer chamber made of thick mild steel sheet. Painted with hammer tone paint finish. The gap between the walls is fitted with special grade glass wool. Heavy duty forced air blowers are provided to constantly circulate hot air to achieve uniform temperature in the chamber.

Drying Oven Industrial RSTI-104 Series Kanthal wire heating elements provided to attain quick and uniform heating in range of 50 DegreeC to 250 DegreeC +2-3 DegreeC controlled by hydraulic type capillary thermostat.

An dial type thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.

Sizes are available

• 900x600x600 mm
• 1200x900x900 mm
• 1500x900x900 mm
• 1800x1200x900 mm

Optional

• Timer 0-99 hours
• Digital PID temp. Indicator-cum-controller

Standard Double Wall Fabrication, inner & outer chamber made of thick mild steel sheet. Painted with hammer tone paint finish. The gap between the walls is fitted with special grade glass wool. Provided with two or three removable shelves. Kanthal wire heating elements provided on three sides to attain quick and uniform heating in range of 30 DegreeC to 110 DegreeC + 1 DegreeC controlled by hydraulic type capillary thermostat. Incubator Bacteriological Thermostatic RSTI-107 Series An L- Shaped prismatic thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.

Sizes are Available:

• 300x300x300 mm
• 350x350x350 mm
• 400x400x400 mm
• 600x450x450 mm
• 600x600x600 mm

Optional:

• Air circulating fan
• Timer 0-24 hours

Laminar Air Flow - Horizontal RLAH-58 Series
Structure made of 19 mm Thick Ply board covered with melamine lamination finish or mild steel duly powder coated or stainless steel. Work bench of perforated stainless steel in all models. Sides of work bench covered with transparent acrylic sheet/melamine. Front acrylic door of collapsible type. Properly balanced blowers fitted on H.P. Electric motor provided on the top portion to supply sufficient air to HEPA filter. HEPA filter provided vertically on back of the work bench to provide clean air to the work bench horizontally. HEPA filter efficiency 99.97%, partial retention >0.3 micron. Pre-filters efficiency 90.0%, partial retention >5.0 micron. One fluorescent tube and one U.V. Germicidal tube provided over work bench. Cock for gas on work bench. Static pressure manometer fitted on top. Laminar Air Flow Horizontal Blowers, motor and pre-filters fitted in lower portion of the cabinet.

Made of thick play board covered with white sunmica & epoxy painted inside. Laminar flow fitted with microprocessor control digital display with filter failure alarms.

Model Sizes

• RLAH-58-01 60x60x60 mm.
• RLAH-58-02 90x60x60 mm.
• RLAH-58-03 120x60x60 mm.
• RLAH-58-04 180x60x60 mm.

Structure made of 19 mm Thick Ply board covered with melamine lamination finish or mild steel duly powder coated or stainless steel. Work bench of perforated stainless steel in all models. Sides of work bench covered with transparent acrylic sheet/melamine. Front acrylic door of collapsible type. Properly balanced blowers fitted on H.P. Electric motor provided on the top portion to supply sufficient air to HEPA filter. HEPA filter provided vertically on back of the work bench to provide clean air to the work bench horizontally. HEPA filter efficiency 99.97%, partial retention >0.3 micron. Pre-filters efficiency 90.0%, partial retention >5.0 micron. One fluorescent tube and one U.V. Germicidal tube provided over work bench. Cock for gas on work bench. Static pressure manometer fitted on top. Laminar Air Flow Horizontal Blowers, motor and pre-filters fitted in lower portion of the cabinet.

Made Of thick ply board covered with white sunmica & epoxy painted inside. laminar fitted with switches for blower, fluorescent light & UV light.

Model Sizes

• RLAH-58-05 60x60x60 mm.
• RLAH-58-06 90x60x60 mm.
• RLAH-58-07 120x60x60 mm.
• RLAH-58-08 180x60x60 mm.

Complete S.S construction fitted with microprocessor control digital display and filter failure alarms.

Model Sizes

• RLAH-58-09 60x60x60 mm.
• RLAH-58-10 90x60x60 mm.
• RLAH-58-11 120x60x60 mm.

Laminar Air Flow - Horizontal RLAH-58 Series (3)

Structure made of 19 mm Thick Ply board covered with melamine lamination finish or mild steel duly powder coated or stainless steel. Work bench of perforated stainless steel in all models. Sides of work bench covered with transparent acrylic sheet/melamine. Front acrylic door of collapsible type. Properly balanced blowers fitted on H.P. Electric motor provided on the top portion to supply sufficient air to HEPA filter. HEPA filter provided vertically on back of the work bench to provide clean air to the work bench horizontally. HEPA filter efficiency 99.97%, partial retention >0.3 micron. Pre-filters efficiency 90.0%, partial retention >5.0 micron. One fluorescent tube and one U.V. Germicidal tube provided over work bench. Cock for gas on work bench. Static pressure manometer fitted on top. Laminar Air Flow Horizontal Blowers, motor and pre-filters fitted in lower portion of the cabinet.

Made of mild steel duly powder coated fitted with microprocessor control digital display and filter failure alarms.

Model Sizes

• RLAH-58-12 60x60x60 mm.
• RLAH-58-13 90x60x60 mm.
• RLAH-58-14 120x60x60 mm.

Controls: Analog

No. of rollers: 4

Speed: 33 RPM Approx

Max Load Kg: 5

Timer: No

Ambient Temp Range: +4°C to +60°C

Rocking & Rolling action for complete mixing.

Power Supply: 230V±10% AC, 50 Hz

Additional Information:

• Item Code: Model-524
• Production Capacity: 10 units
• Delivery Time: 10-15 days
• Packaging Details: cardboard box

Orbital Shaking Incubator RSTI-111 Series
Outer made of M.S. Sheet powder coated & inner chamber is made of thick S.S. Sheet. The gap between two walls is fitted with high grade glass wool. The glass window makes it possible to inspect specimen without disturbing inner Temperature. The unit has a temp. range from ambient to 60 Degree. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator Cum Controller with a accuracy of + 0.5 DegreeC. Air Circulation Fan is provided to maintain stability throughout. Speed of shaker is variable from 30 RPM to 250 RPM. Orbital Shaking Incubator RSTI-111 Series The tray of the shaker is also made of S.S. Sheet with Lotus type clamps to hold flasks. Unit is fitted with Digital RPM Meter, 999 min digital time.

Capacity (ml)

• 9 Flasks of 250ml.
• 16 Flasks of 250ml.
• 16 Flasks of 500ml.

Optional Accessories

• Timer 0-24 Hours
• 16 Flasks of 100ml. instead of 9 flasks of 250ml.
• 9 Flasks of 500ml or 25 flasks of 100ml instead of 16 flasks of 250ml.
• 25 Flasks of 250ml or 36 flasks of 100ml instead of 16 flasks of 500ml.

Orbital Shaking Incubator-cum-B.O.D RSTI-112 Series
Orbital shaking incubator cum B.O.D incubator is specifically designed to controlled incubation with orbital shaking arrangement with powerful geared motor for many labotatory procedures such as tissue culture, fermentations studies, enzyme reactions, growth studies etc. The outer chamber is made up of M.S sheet duly powder coated & inner chamber is made of thick S.S. sheet. The gap between wall is fitted with high grade glass wool to avoid thermal loss. The plexi glass window provided to inspect the specimen without disturbing the inner temp. The incubator is illuminated with one door operated or panel operated flurescent tube. The unit has a temp. Range from 5 DegreeC to 60 DegreeC. The temperature is controlled by Dual Display Microprocessor PID Temperature Indicator cum Controller with a accurancy of + 0.5 DegreeC. Air circulation fan is provided to maintain stability throughout. The speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S sheet with lotus type clamps to hold flasks. The unit is fitted with Digital RPM meter, 999 min digital timer. Orbital Shaking Incubator-cum-B.O.D RSTI-112 Series.

Capacity (ml)

• 16 Flasks of 500ml.
• 25 Flasks of 250ml.
• 36 Flasks of 100ml.

Optional Accessories

• Timer 0-24 Hours
• Automatic voltage stabilizer 3KVA (Most rec.)

Serological Water Bath RSTI-134 Series
These units are double walled with inner chamber made up of S.S. Sheet and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses. The inner chamber fitted with immersion type heating element is covered with perforated removable diffuser tray. The cover is provided with the unit as a standard accessory. Temperature from ambient to 100 DegreeC is controlled by Hydraulic capillary type thermostat with accuracy of + 1 Degree C. Workable on 220V AC 50Hz Single Phase.

Inner Chamber Sizes are available

• 300x175x175 mm
• 300x250x175 mm
• 375x300x175 mm
• 455x300x175 mm
• 605x300x175 mm

Optional

• Microprocessor PID digital temp. Indicator cum controller.
• Stirrer with 1/20 Hp motor with S.S. rod blade.
• Auto cut off device when water level is low.

Additional Information:

• Item Code: RWD-5
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: AMBALA
• Production Capacity: 10 PCS / PM
• Delivery Time: 15-20 DAYS
• Packaging Details: CARD BOARD

Easy to operate with any size of Dispenser Pump Bottle (Bottle not Included)

Hand Touch Free, Long Lasting, Good Quality, Very Sturdy and Maintenance Free

Adjustable canister for any bottle size.

Suitable for Business Premises, Hospitals, Restaurants, Educational Institutes and Home also.  

Adjust Bottle up to 1 Ltr.

Material mild steel with powder coated

Weight 4-5 kg approx

Durable and easy to use.

Additional Information:

• Production Capacity: 500
• Delivery Time: 10 days

We are offering Essential Oil Steam Distillation kit made from borosilicate glass. This kit Comprising of 1 Stove, 500ml Round Bottom Flask (can be customized), Steam Distillation Head, Leibig Condenser, Receiver Adapter and Receiver Flask 250ml (can be customized), Joints & Clamps.

Additional Information:

• Packaging Details: Export worthy packaging

Standard Double Wall Fabrication. Outer painted with hammer tone paint finish. The gap between the walls is fitted with special grade glass wool. Heavy duty forced air blowers are Provided to constantly circulate hot air to achieve uniform temperature in the chamber.

Tray Dryer RSTI-105 Series Kanthal wire heating elements provided to attain quick and uniform heating in range of 50 DegreeC to 250 DegreeC +2-3 DegreeC controlled by hydraulic type capillary thermostat.

An dial type thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.

Sizes are available

• 430x840x650 mm
• 430x840x910 mm
• 910x840x910 mm
• 960x1270x1440 mm
• 960x1700x1700 mm

Optional

• Timer 0-99 hours
• Digital PID temp. Indicator-cum-controller

Blood Bank Refrigerator RSTI-126 Series
Blood bank refrigerator is a most versatile unit for blood bank. The inner chamber is made of stainless steel sheet and outer of PCRC sheet duly powder coated. Mounted on sturdy iron frame with castor wheels for easy mobility. The temperature is maintained between 4 to 6 DegreeC with forced air circulation ensures uniform temperature, for storing blood bottles or blood bags. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator cum Controller. Audio/visual Alarm triggers in the event of temperature fluctuations. Unit is also fitted with Door open alarm & Power Supply /Failure Alarm as a safety device.

Highly efficient refrigeration unit is housed on bottom. Two doors are provided. Inner door is transparent made of lexiglass, for viewing the chamber. Drawers are provided for holding bags. Workable on 220 V AC.

Capacity No. of Blood Bags:

• 85L 50Bags
• 165L 110Bags
• 200L 180Bags
• 280L 250Bags
• 400L 360Bags

Optional:

• Chart type temperature recorder
• Automatic voltage Stabilizer 3-5 KVA (Most rec.)

The inner chamber in made of stainless. Steel sheet and outer of PCRC sheet duly powder coated. Mounted on sturdy iron frame with castor wheels for easy mobility. The temperature is maintained between 4 to 6 DegreeC with forced air circulation ensures uniform temperature, for storing medicines. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator cum Controller. Laboratory Refrigerator RSTI-127 Audio/ Visual Alarm triggers in the event of temperature fluctuations. Highly efficient refrigeration unit is housed on the bottom.

Two doors are provided. Inner door is transparent made of plexiglass, for viewing inside the chamber. Drawers are provided for holding medicines. Workable on 220 V AC.

Chamber In Size

• 455x410x610 mm
• 505x415x830 mm
• 565x565x865 mm
• 650x580x900 mm

Biosafe Cabinet (Mild & Stainless Steel)

The Class-II Biological Safety Cabinet is an open-front, ventilated cabinet. Which provide personnel, environment and product protection.

Biosafe Cabinet (Mild Steel) Class II, A-2

Item Code Size

• RS-59-05 60x0x60 cm
• RS-59-06 90x60x60 cm
• RS-59-07 120x60x60 cm

• Large radius inside corners for easy clean up
• Heavy gauge stainless steel & conveniences and state-of-the-art engineering.
• Mounted on stainless steel tubular stand for providing maximum efficiency.
• Provided with two body-supports of width 6" and head rest.
• Chrome plated swing spout mixing faucet for hot and cold water and lever handle for waste & drain along with deep & large s. s. sink.

Additional Information:

• Item Code: RSP3S
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Ex-works, Ambala
• Production Capacity: 10 pieces/month

Laboratory Round Hot Plates RSTI-145 Series
Laboratory hot plates are available in round and rectangular shapes. Body is fabricated out of thick mild steel duly finished with powder coating. Heater made of kanthal wire to operate on 220 V AC 50 Hz single phases. Heat is controlled by three point rotary switch or energy regulator with an indicator lamp for main etc.

Available in following options

• 8" dia
• 8" dia x two plates
• 8" dia (20 cms) round spiral

Laboratory Rectangular Hot Plates RSTI-146 Series
Laboratory hot plates are available in round and rectangular shapes. Body is fabricated out of thick mild steel duly finished with powder coating. Heater made of kanthal wire to operate on 220 V AC 50 Hz single phase. Heat is controlled by three point rotary switch or energy regulator with an indicator lamp for main etc.

Available in M.S. Top / C. Iron Top / S.S Top, as customer requirement.

Available in following sizes:

• 12" x 10"
• 16" x 10"
• 18" x 12"
• 24" x 18"

Slide Warming Hot Plate RSTI-147 Series
With Temp. Control upto 80 Degree C for drying slides at low temperatures. Fitted with energy regulator. Workable on 220V AC 50Hz single phase.

Available in following sizes:

• 12" x 10"
• 16" x 10"
• 18" x 12"
• 24" x 18"

Bio Therm Heating Stage
It can afford the constant temperature and can be mainly applied to the microscope that used in the biological technology for special request of constant temperature when viewing the specimen (Living Cell).

Convenient Installation It can be installed on any standard stages of Microscope. Quick reaching constant temperature After plugging in the power & setting the temperature, it takes 1-2 minutes to preheat the stage & reach the constant temperature in the certain range of temperature.

Temperature Controller 2 LED digital display screens and two touching buttons for adjusting temperature, ON/OFF switch at the rear.

Temperature Controlled Stage Built - in heater and heat sensor with the size of 150mmx130mmx5.8mm.

Additional Information:

• Production Capacity: 5
• Delivery Time: 30 days

Postmortem Autopsy Table RSPA-3SD

• These are specially designed for all kinds of postmortem work.
• The construction of these tables incorporates state-of-the-art engineering, heavy gage stainless steel and conveniences.
• Autopsy stainless steel table mounted on stainless steel tubular stand.
• Scientifically designed for maximum efficiency.
• Large radius inside corners for easy clean up.
• Engrave measurement scale on one side for easy measurement of cadaver.

Provided with Two Nos 6" wide body-supports (S. Steel) removable type, six position head rest, crusher (grinder/aspirator) for disposal, chrome plated swing spout mixing faccuet for hot and cold water, lever handle for waste/drain and deep & large S. S. Sink with overflow.