Reliant Lab

Power	100 watts
Voltage	115V-220V
Phase	Single Phase
Frequency	50/60Hz
Floor Area	0.75 m x 1.5 m

The apparatus has been designed to introduce students to the fundamental characteristics of the behaviour of the particle system, in particular the relationship between the drag coefficient of falling particles and Reynolds number. Particles covering a range of sizes and densities are supplied and the experiments are conducted by allowing single particles to fall through a number of different liquids contained in a vertical glass tube. The rate of fall of the particle is determined by timing their passage between two marks on the walls of the glass tubes. Observation of the particle movement is aided by the provision of a shielded fluorescent tube light mounted on the backboard. Particles can be removed from the bottom of the tubes without the necessity of draining the liquid. A valve system is provided at the bottom of each tube to allow the particles to be removed with the minimum loss of liquid.

Additional Information:

• Item Code: RLMMT-104
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Phase	Single Phase
Brand	Reliant lab
Current	5-15 amp
Floor Area	0.75 m x 0.75 m.
Voltage	220 VAC
Frequency	50 Hz
Earth voltage	Less than 5 volts
Mercury	250 ml.

Backed by profound experience of our experts, we are an unparalleled name engaged in providing a high-quality assortment of Through Packed Bed Pressure Drop

Details:
The set-up consists of a glass column packed with packing material i.e. Rasching rings, SS mesh to support the packing and with calming section. Pressure drop across packed bed can be measured by a manometer. The apparatus is close circuit type provided with tank, pump, necessary piping, valves and rotameter to measure the flow rate of fluid. The set-up is fitted on a MS frame and painted with good quality corrosion resistant paint.

 Experimentation:

• 
  To study relationship between velocity of fluid and pressure drop per unit packed length.
• 
  To plot graph between modified friction factor & modified Reynolds number.

Additional Information:

• Item Code: RLMMT-101
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Material	Stainless Steel
Phase	Single Phase
Frequency	50Hz
Coating	Powder Coating
Voltage	220 VAC

Helical coils are used for heating or cooling in process tanks. When a fluid flows through a curved tube, centrifugal force acting upon the various elements of fluid moving with different velocities causes secondary circulation. Secondary flow results in higher heat transfer characteristics. Further, secondary flow stabilizes the laminar flow leading to a higher critical Reynolds number for transition from laminar to turbulent flow.

Additional Information:

• Item Code: RLMMT-103
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Material	Mild Steel
Usage/Application	Laboratory
Brand	Reliant Lab
Voltage	230V-380V
Frequency	50/60Hz
Coating	Powder Coating

An Elutriator is vertical tube through which a fluid passes upwardly at a specific velocity while a solid mixture, whose separation is desired, is fed into the top of the column. The large particles, which settle at a velocity higher than that of the rising fluid, are collected at the bottom of the column, and the smaller particles are carried out of the top of the column with the fluid. Several columns of different diameters in series may be used to bring about a further separation. The set up consists of two vertical tubes of different diameter in which water is passed at a controlled velocity. A tank with pump is provided for re-cycled water supply and flow rate is measured by Rotameter and controlled with the help of control valve. The tubes are arranged in a fashion of ascending cross-section area. The particles are introduced through a feed hopper provided at first tube, the smaller particles are carried over in the fluid stream, while the large particles settle against the upward stream. The overflow from the first tube introduced at the bottom of second tube is passed vertically upwards and the overflow from the second tube introduced at the, is passed to drain. The weighed sample originally placed in the first tube of smallest diameter is classified into fractions according to their settling velocities. The fractions are collected in successive tubes by a special arrangement and may be dried and weighed to make analysis.

Additional Information:

• Item Code: RLMMT-115
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Capacity	2-10 (T/h)
Voltage	220 V AC
Frequency	50Hz
Material	Mild Steel
Phase	Single Phase
Motor	2.5-44 kW

The Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed. They have relatively narrow faces and are larger in diameter so that they can nip moderately large lumps. Loading bolts are provided for safety. The maximum size of the product is approximately equal to gap between the rolls & it can be adjusted by loading bolts.

Additional Information:

• Item Code: RLMMT-107
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Power	110W
Voltage	220V-320
Phase	Single Phase
Brand	Reliant Lab
Material	Stainless Steel
Coating	Powder Coating
Frequency	50Hz

The setup consists of a glass column with fluidizing material i.e. beads, S.S. mesh to support the beads and with calming section. Pressure drop across fluidization can be measured by manometer. The setup studies in fluidization characteristics and relationship between the velocity of the fluid and pressure drop per unit length. The apparatus is close circuit type provided with suitable capacity tank, FHP pump, necessary pipeline valves and a Rotameter to measure the flow rate of fluid. The setup is fitted on a MS frame painted with good quality paint.

Additional Information:

• Item Code: RLMMT-102
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Voltage	220 V AC
Floor Area	1.5 m x 1 m
Width	380 mm
Drive	Eccentric Shaft Coupled to Motor
Length	600 mm
Mesh	12.7 mm,9.5 mm and 6.3 mm
Control Panel Comprises of	Standard Make On/Off Switch,Mains Indicator etc
Instruction manual	An English instruction manual will be provided along with the apparatus
Feed Hopper	Compatible Capacity with Arrangement to Control Feed
Collecting Bins	4 Nos. of Suitable Capacity
Electric Supply	Single Phase,0.5 kW

Vibrating screens are those, which rapidly vibrated with small amplitude, are less likely to blind than gyrating screens. The vibrations may be generated mechanically or electrically. Mechanical vibrations are usually transmitted from high-speed eccentrics to the casing of the unit and from there to inclined screens. The setup consists of three different screen with fitted on a rigid M.S. frame, feed hopper, eccentric etc. Three screens of different sizes are fitted one above the other. The drives are given from an electric motor.

Additional Information:

• Item Code: RLMMT-110
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Material	Mild Steel
Voltage	220/230V A.C.
Frequency	50Hz
Brand	Reliant lab
Dimensions	400mm L x 385mm W approx.
Usage	Laboratory

The rotap sieve shaker reproduces the circular and tapping motion given to test sieves in hand sieving. The uniform, mechanical action ensures accurate and dependable test. Using the regular height 20-cm diameter sieves, one sample can be tested on a series of six sieves of different openings, all with one operation of machine. The Rotap Sieve Shaker is simple and durably constructed and is run by a motor. The running parts operate in oil. The machine is easily installed. No special foundation is required. Test Sieves are supplied at extra cost. A time switch from 0 to 60 minutes is provided.

Additional Information:

• Item Code: RLMMT-112
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Material	Mild Steel
Coating	Powder Coating
Motor Power	1 HP
Voltage	220 V-320V
Frequency	50Hz

Mixed liberated particles can be separated from each other by floatation if there is sufficient difference in their wet-ability. The floatation process operates by preparing a water suspension of a mixture of relatively finely sized solids. This is usually done in an agitated chamber open at the top. Fine bubbles of air are then dispersed through the agitated suspension to form a froth that rises to the top of the chamber. Particles that are radially wetted by water (hydrophilic) tend to remain in the water suspension. Those particles that are not easily wetted (hydrophobic) tend to be collected at the air bubble-water interface and rise to the surface attached to air bubbles. Thus differences in the surface chemical properties of the solids are the basis for separation. The set up consists of a agitated chamber open at the top. In the chamber, an impeller coupled to a shaft is fixed in a stationary diffuser. Low-pressure air is allowed to enter in the stationary diffuser through the air passage provided with the agitator. The collector coated mineral particles adhere to the rising bubbles and are carried to the top of the cell to be removed in the froth product

Additional Information:

• Item Code: RLMMT-117
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Voltage	220V
Material	Mild Steel
Frequency	50Hz
Suitable For Wet Sieving	Yes
Motor Power	1.5 HP
Application	Educational equipment
Diameter	20cm

Gyratory type shaker is driven by FHP motor through a reduction gear suitable to carry upto 7 sieves of .When clamped the sieve table does not rotate but it is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction. In addition to the gyratory motion of the shaker, there is an upward and downward movement ensuring that each square inch of the sieve is utilised. The whole mechanism runs in an oil bath. Test Sieves will be supplied at an extra cost. A time switch from 0-60 minutes is provided

Additional Information:

• Item Code: RLMMT-113
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Material	With SS mesh & filter cloth on both sides
Slurry Tank Capacity	50 Litres (Approx.)
Agitator Material	Stainless Steel
Vacuum Pump	Standard Make Coupled To Fhp Motor
Electric Supply	Single Phase, 220 V Ac, 1kw
Floor Area	1m X 1.5m
Leaf Filter Diameter	200 mm

Leaf filters, sometimes called tank filters, they consists of flat filtering elements (leaves) supported in a shell. The leaves are circular, arc-sided, or rectangular, and they have filtering surface on both faces. The shell is a cylindrical tank The set-up consists of flat filtering elements (leaves) supported in a slurry tank. A filter leaf consists of a perforated plate over which a filter medium of woven fabric is fitted. The whole assembly is connected to a vacuum pump through a filtrate receiver. An agitator is fitted in the slurry tank. Drain valve is provided in it. The set-up is operated batch wise.

Additional Information:

• Item Code: RLMMT-121
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Material	Mild Steel
Brand	Reliant Lab
Coating	Powder Coating
Motor Power	1 HP
Voltage	230V-380V
Frequency	50/60Hz

A jig is a mechanical device used for separating materials of different specific gravity by the pulsation of a stream of liquid flowing through a bed of material. The setup consists of plunger operated by crank mechanism connected to motor coupled with reduction gear box. Sump tank with pump is provided for water circulation.

Brand	Reliant lab
Stirrer	Stainless Steel Impeller with Stainless Steel Shaft Coupled to Fhp,Dc Motor and Thyristor Controlle
Agitator	Stainless Steel Shaft & Impellers (I.E. One Propeller & One Turbine)
Baffles	Material Stainless Steel,4 Nos. 50mm Width. (Detachable)
Digital Voltmeter	0-300 Volts
Ammeter	0-5 Amps
Diameter	300 mm
Depth	450 mm

For a processing vessel to be effective the volume of fluid circulated by the impellers must be sufficient to sweep out the entire vessel in a reasonable time. The velocity of the stream leaving the impeller must be sufficient to carry the current to the remotest parts of the tank. Liquids are most often mixed in some kind of tanks or vessels, usually cylindrical in form and with a vertical axis. Tank bottom is rounded to eliminate regions into which the fluid currents would not penetrate. In the present set-up mixing is done with the help of stirrer. The stirrer is complete with SS Impeller with SS Shaft coupled to FHP DC motor. The speed of agitator can be varied with the help of Thyristor controlled DC Drive and power consumption is measured by Digital Voltmeter & Digital Ammeter. Four replaceable baffles are provided to prevent swirling. One 4-bladded propeller and one 6-bladded turbine are provided which are interchangeable. Drain valve is also provided at the bottom. Effectiveness of power consumption in fluid mixing can be performed with and without baffles hence increasing the range of experimentation. The whole set-up is mounted on a rigid MS frame structure

Additional Information:

• Item Code: RLMMT-124
• Pay Mode Terms: T/T (Bank Transfer),D/P,D/A

Brand	Reliant Lab
Drive	Fhp Motor With Reduction Gear Box
Collecting Bin	2 Nos. one Each For Magnetic and Non-Magnetic Material
Electric Supply	Single Phase, 220 V AC, 1 kW
Floor Area	1.5 X 1 m
Belts Width	150 mm
Belts Length	500 mm
Feed Hopper Material	Stainless Steel
Control Panel Comprises of	Standard Make On/Off Switch, Mains Indicator etc

We are amongst the reputed organizations, highly engaged in offering an optimum quality range of Magnetic Separator.

Details:
Materials, that have different magnetic attractability, may be separated by passing them through a magnetic field. Most often, magnetic separation techniques are used to remove iron, steel or magnetic iron oxide from materials low in magnetic attractability. These devices operate in either a continuous or a cyclic manner. Continuous devices usually have a belt which moves over the lifting magnetic poles to carry the magnetize partials into a region of low or zero magnetic field, where they are released. The present set-up is of In-line lifting magnet type. The set-up consists of two belts moving separately in opposite direction at slow speed. Feed through a vibrating hopper is conveyed over first belt and allowed to pass near the second belt, which is under magnetic field. The magnetic field is generated by permanent magnet kept in a box. Magnetically inert material drops off the belt in a normal manner. Magnetic material is held on the belt, however, and finally drops off the belt as it leaves the magnetic field. Both the belts are fitted on the pullies and drived by an electric motor coupled with a reduction gearbox.