R.R. Chemtech Corporation

FMB70

Measuring range  : 0.1 to 10 bar rel.

Accuracy                : ±0.075%

Temperature         : –10 to +100°C (14 to 212°F) (+135°C (275°F) for 30 minutes maximum)

The FLXA21 is 2-wire module-type liquid analyzer that can be connected to up to two detectors from pH /ORP meters, conductivity meters, inductive conductivity meters, and dissolved oxygen meters.

By connecting two detectors of the same type, a more reliable system can be constructed as a high-precision duplex system.

And the impedance, asymmetric potential, slope, etc. of the detector are constantly measured, and continuously diagnostics status such as the electrode is dirty, damaged, broken and low measurement liquid level.

This self-diagnosis function of the detector reduces maintenace costs and improve OPEX.

• Chemical and petrochemical industries
• Process engineering
• Pharmaceutical industry
• Food and beverage industry
• Hazardous areas

1. Pneumatic connection, port 1                                                                           G1/2
2. Standard nominal flow rate (standardised to DIN 1343)                            3400 l/min
3. Pressure regulation range                                                                        0.5 bar - 12 bar
4. Grade of filtration                                                                                              40 µm

The pressure transmitter, type MBS 3000, is designed for use in almost all industrial applications, and offers a reliable pressure measurement, even under harsh environmental conditions.

MBS 3000 is designed to cover requirements in most environments and therefore it is a highly flexible product widely used in most applications
The version consists of two series:
MBS 3000 – without integrated pulse-snubber
MBS 3050 – with integrated pulse-snubber

The integrated pulse-snubber offers a high degree of protection against cavitations and liquid hammer, and the well thought out design results in excellent vibration stability and an exceptional robustness.

The flexible pressure transmitter program covers different output signals, absolute and gauge (relative) versions, measuring ranges from 0 – 1 to 0 – 600 bar and a wide range of pressure and electrical connections.

Excellent vibration stability, robust construction, and a high degree of EMC/EMI protection equip the pressure transmitter to meet the most stringent industrial requirements.

Designed for use in almost all industrial environments

Resistant to cavitation, liquid hammer and pressure peaks (MBS 3050)

Enclosure and wetted parts of acid-resistant in it's fully welded design - Stainless steel (AISI 316L)

High Performance

Robust, shock- and vibration-resistant solution with high-electromagnetic compatibility harsh water, and air, and marine applications.

Longer component lifespan and reduced warranty cost.

Pressure ranges in relative (gauge) or absolute from 1 up to 600 bar

All standard output signals: 4 – 20 mA, 0 – 5 V, 1 – 5 V, 1 – 6 V, 0 – 10 V, 1 – 10 V

A wide range of pressure and electrical connections

• Best-in-class precision of ≤ 0.3 %FS
• Compact sensor design, easy & uniform operation
• Pressure measurement up to 60 bar
• All-welded stainless steel design
• IO-Link dual-channel interface for easy commissioning

• This provides a Total Error Band of ±2% over the operating temperature range of -40ºC to125ºC [-40°F to 257°F].
• New standard configurations are regularly being added.The PX2 Series is compatible with a variety of harsh media including brake fluid, refrigerants, engine oil, tap water, hydraulic fluids, and compressed air.
• The wide operating temperature range, ingress protection up to IP69K, and 100V/m radiated immunity to allow for reliable performance in tough environments.
• These transducers measure absolute or sealed gauge pressure. The absolute versions have an internal vacuum reference and an output value proportional to absolute pressure.
• The sealed Gage versions have an internal pressure reference of one atmosphere at sea level.
• Item Code: PX2-Pressure-Sensor
• The PX2 Series is available in three pressure ranges, with additional pressure ranges coming soon

• Gauge Pressure
  • EJA530E
  • EJX530A
  • EJX630A
  • EJA430E
  • EJX430A
  • EJA438E
  • EJX438A
  • EJA440E
  • EJX440A
  • EJXC40A (Digital Remote Sensor)
  • EJXC80A, EJAC80E (Differential / Gauge Pressure Diaphragm Seal)
  • EJXC50A, EJAC50E (Gauge Pressure Direct Mounted Seal)

The Series MSX Magnesense® Differential Pressure Transmitter combines the stability and versatility of the original Series MS2 Magnesense® II transmitter for use in building control applications. The MSX simplifies the ordering process to deliver the desired configuration, which reduces product setup time. Pressure ranges are available in Pa, mm w.c., and in w.c. All pressure ranges can be configured in unidirectional or bidirectional modes, providing a total of 32 ranges. The MSX transmitter can provide a linear pressure output or a linear velocity output with the square root extraction from the transmitter. Additional parameters have been included to expand the square root capability for calculating flow. Dual voltage and milliamp output signals can be used to provide both control and equipment output signal verification.

NIST CALIBRATION available in Product Configurator.

Series 3100D Smart Pressure Transmitter is a microprocessor-based high performance transmitter, which has flexible pressure calibration, push button configuration, and programmable using HART® Communication. The Series 3100D is capable of being configured for differential pressure or level applications with the zero and span buttons. A field calibrator is not required for configuration. The transmitter software compensates for thermal effects, improving performance. EEPROM stores configuration settings and stores sensor correction coefficients in the event of shutdowns or power loss. The Series 3100D is FM approved for use in hazardous (classified) locations. The 100:1 rangeability allows the smart transmitter to be configured to fit any application.

• Flow measurement
• Level monitoring
• Filter or pump differential pressure
• Critical process monitoring

Brand

Maximum Operating Pressure

250 bar

Minimum Operating Pressure

25bar

Pressure Type

Positive Pressure

Suitable Media

Fluid, Oil

Manufacturer Series

18D

Contact Operation

Normally Closed, Normally Open

Minimum Operating Temperature

-20°C

Maximum Operating Temperature

+80°C

IP Rating

IP65

Pressure Setting Range

11 → 17bar

Minimum Pressure Setting

11bar

Maximum Pressure Setting

17bar

The EJX-A series is Yokogawa's premium performance line of DPharp transmitters. Released in 2004, it offers the performance and stability needed in demanding applications. The EJX-A series performance makes it the thoroughbred of the DPharp family of pressure transmitters.

The EJX530A is an In-Line Gauge Pressure Transmitter in the series.

EJX530A standard features include:

• ± 0.04% Accuracy
• ± 0.1% per 15 years Stability
• 90 ms Response Time
• Exida and TUV SIL 2/3 Certified
• Local Parameter Setting (LPS)

The EJA-E series of transmitters is Yokogawa's most recent evolution of the DPharp family of pressure transmitters. Released in 2012, it combines the ruggedness and success of the work-horse EJA-A series with the performance of the thoroughbred EJX-A series to deliver the type of product you have come to expect from Yokogawa.

The EJA210E is the Flange-mount Liquid Level Transmitter in the series.

EJA210E features include:

• ± 0.075% Accuracy
• ± 0.1% per 1 year Stability
• 120 msec Response Time
• Exida and TUV SIL2 / SIL3 Certified
• Signal Characterizer for the 4 to 20 mA output
• Local Parameter Setting (LPS)

FTL50H/51H

Temperature     : -50 to +150°C

Pressure              : -1 to +100bar

Protection           : IP66/67

Sensor material : 316L

Application

Food and Pharmaceutical Products, Suitable for hazardous areas

FTL51C

Temperature     : -50 to +150°C

Pressure              : -1 to +40bar

Protection           : IP66/67

Sensor material : ECTFE, PFA (Edlon, Rubyred, conductive), Enamel

Application

Point level switch with extension tube and highly corrosion resistant coating

FTL50

Temperature     : -50 to +150°C

Pressure              : -1 to +64bar

Protection           : IP66/67

Sensor material : 316L, Alloy

FTL51

Temperature     : -50 to +150°C

Pressure              : -1 to +100bar

Protection           : IP66/67

Sensor material : 316L, Alloy

FTL85

Temperature     : -50 to +150°C (-76 to +300°F)

Pressure              : -1 to +40bar (-14.5 to +580psi)

Sensor length    : Extension pipe up to 3m (9.8ft)

Sensor material : Enamel, ECTFE and various PFA materials

Process connections: Threads and flanges

FTL81

Temperature     : -60 to +280°C (-76 to +540°F)

Pressure              : -1 to +100bar (-14.5 to +1,450psi)

Sensor length    : Extension pipe up to 3m (9.8ft)

Sensor material : 316L, Alloy C

Process connections: Threads and flanges

FTL80

Temperature     : -60 to +280°C

Pressure              : -1 to +100bar

Sensor material : 316L, Alloy

Sensor length    : Extension pipe up to 3m (9.8ft)

Process connections: Threads and flanges

FTL825

Ambient temperature   : -20 to +60°C

Mounting                        : DIN Rail Channel/ In Panel