S.K.Associiates

Adhesive for fixing vitrified tiles on the floor as well as for tile-on-tile application

• Ready to mix
 
• Self curing
 
• Easy to use
 
• High compressive strength
 
• Good coverage
 
• Tile on tile application
 
• High bond strength
 
• Single component product
 
• Low prorosity tiles
 
• High durability

Floor, Wall

weberset classic is a high polymer modified thin-set tile adhesive, specially formulated for fixing low porosity vitrified tiles on the floor in internal areas. The adhesive can be used for fixing ceramic tiles on wall and floor and is suitable for dry as well as wet areas for internal application. This is also suitable for tile-on-tile application for fixing vitrified tiles on pre-existing ceramic tile floors.

• High Bond strength.
• The free-flowing product makes it easier to mix and apply, easy-to-use.
• Useful for bed thickness of 3-15* mm. May go up to 15 mm in a limited extent for wall & floor application.
• Thixotropic formula - no sag, for the easy application on the wall.
• Low VOC – For a healthy living.
• For installation of vitrified tiles on the floor.
• Suitable for internal use only.
• Suitable for Tile-on-tile application of vitrified tiles on pre-existing ceramic tile floors.
• Self-curing properties, which allows for no-hassle application, with minimum labour.
• No hacking of the substrate required to achieve the required bonding.
• Do not use for large format tiles.
• Do not use in external areas, or areas exposed to direct sunlight.
• Do not use for fixing vitrified tiles on walls.
• Do not use for fixing stones.
• Do not use on the wet screed. The surface must be fully cured.
• Do not use for installing glass mosaic, glass tiles, or metal tiles. Use only weberset glass mosaic for fixing glass mosaics, and only weber epoxy adhesive for fixing glass and metal tiles.
• Do not use for wooden flooring, for insulating and soundproofing panels.
• Do not use on waterproofing coat – If waterproofing is required, use webertec SBR and
• webertec crete for the same. Refer to the respective datasheets for details.

Adhesive for window framing , tile cladding and natural stone flooring

Ready to mix 

• Self curing
 
• Easy to use
 
• High compressive strength
 
• Good coverage
 
• Tile on tile application
 
• High bond strength
 
• Submerged conditions
 
• Wall cladding
 
• Single component product
 
• Low prorosity tiles
 
• High durability

Wall, Floor

weberset plus-white is a ready to mix, highly polymer modified cementitious adhesive for vitrified, ceramic tile and natural stones of regular size on wall and floor with regular traffic. This product is suitable for fixing granite and other natural stones in window jambs and door frames due to its ability to withstand mechanical operations (which are carried out during fixing doors and windows). White colour adhesive adds to aesthetic look, especially for light colour stones.

• Ready to mix, single component product.
• Recommended for both internal & external surfaces for wall & floor in dry & wet areas.
• Especially suited for fixing low porosity tiles and stones of regular size.
• Suitable for fixing natural stones in window jambs and door entrances.
• Highly polymer-modified: Provides high structural adhesion, which allows to be used on a variety of substrates, for fixing a variety of tiles and stones.
• Excellent adhesion properties, no slip is observed on vertical applications in tiles and natural stones.
• Self-curing properties, which allows for hassle-free application, with minimum labour.
• No shrinkage prevents de-bonding and gives longer life to tiles and stones.
• Low VOC for healthy living.
• Prolonged and easy workability.
• The tiled floor can be made available for foot traffic after 24 hours.
• Can be used for new construction, as well as for renovation over existing floors/facades.
• No hacking of the substrate required to achieve the bonding.
• Useful for bed thickness of 3-12 mm, may go up to 15 mm in a limited extent.
• Do not use on wet screed or plaster. The surface must be fully cured.
• Use on gypsum plaster or boards, fibre cement boards, or other drywall partitions, strictly in accordance with the tile substrate recommendation table.
• Can only be used on cementitious waterproofing. Do not use on epoxy or polyurethane waterproofing.
• Do not use for installing glass tiles or metal tiles. Use only weber bond poxy, for fixing glass and metal tiles.
• Do not use on metal, rubber, plastics, vinyl, linoleum surface, painted substrates. Contact weber representative for a recommendation.
• Do not use on surfaces subjected to vibrations. For vibrations, use weberfix drywall for such areas.

weber shine armor is a two-component, 100% solid, glitter based reaction resin epoxy grout which is acid-resistant. The glitter component is premixed with the resin base which results in a consistent, uniform and highly aesthetically finished joints after application.

• Enhances asthetics
 
• Easy to use
 
• Chemical resistant
 
• Stain resistant
 
• Anti bacterial
 
• Water repellant
 
• High bond strength

Wall, Floor

Part A: Part B - 11.5 : 1 by weight

Part A: Part B - 8 : 1 by volume

• Glitter component is premixed to avoid mixing at the site. This results in consistent, uniform & highly aesthetically finished joints.
• The glittering effect is higher due to reflective filler & transparent resin enhances decorative and durable joints.
• Easy to mix with a creamy consistency which helps in faster application and ease in cleaning.
• Available in attractive & decorative colours.
• High sag resistance formula and thixotropic. Can be used for both floor & wall applications.
• Excellent stain & chemical resistance properties.
• Very low in shrinkage and high resistance to cracks.
• Non-absorbent and water-resistant joints prevent the growth of bacteria and fungus.
• Minimum joint width of 1 mm.
• Maximum joint width of 7 mm in vertical and 14mm in horizontal.
• Do not use the grouts in industrial aggressive chemical prone areas and the areas which are subjected to aggressive cleaning with pressure or steam cleaning.
• At least for 7 days after grouting for acid cleaning & submerged conditions.

Translucent grout

2 components 

Chemical resistant 

Seepage resistant 

Easy to apply and clean

High bond strength 

UV resistant 

Stain resistant 

Crack resistant 

Traffic resistant

weber pearl armor is a two-component, high performance 100% solid epoxy based tile/stone filler which allows light to pass through the grout itself to create a unique reflective appearance. 

• Stain resistant
 
• Water repellant
 
• Anti bacterial
 
• Chemical resistant
 
• Enhances asthetics

• Easy to apply
• Support

  Wall, Floor

Part A: Part B - 11.5 : 1 by weight

Part A: Part B - 7 : 1 by volume

• Highly dense, even, compact and a smooth finish results into nonabsorbent, water resistant surface which prevents the growth of bacteria and fungus.
• Easy to mix with a creamy consistency which helps in faster application and ease in cleaning.
• Very low in shrinkage and high resistance to cracks.
• Excellent chemical & stain resistant properties.
• No-sag resistance formula for wall & floor applications.
• High mechanical strength which results in long durability of the grouts.
• It can resist most of commercial cleaners which are used regularly for cleaning tile and stone.
• Two components pre weighed & ready to mix.
• Being translucent in nature, it can be used for fixing glass blocks and areas were background light is desired which cannot be achieved with a cementitious & resin adhesive.
• Very low in volatile organic compounds which allows it to be to be used in green buildings
• When applied in between tile and stone will result in invisible grouts unlike cementitious and common epoxy grouts.
• High bonding strength with tiles and stones.
• High translucency increases the chromatic effect resulting into highly aesthetic and decorative finish.
• It can withstand heavy traffic and weathering conditions.
• No color shading even when used in wet and submerged conditions..
• Can be used where minimum joint width is 1 mm.
• Can be used where maximum joint width of 7 mm in vertical and 14mm in horizontal.
• Do not use the grouts in industrial aggressive chemical prone areas and the areas which are subjected to aggressive cleaning with pressure or steam cleaning.
• For at least 7 days days after grouting, for acid cleaning & submerged conditions