X

Shellco (Regd.)

Sarai Kale Khan, New Delhi, Delhi

| GST  07ABRPR6748J1ZR

| TrustSEAL Verified

|

★★★★★
★★★★★
View Mobile Number 83% Response Rate

IWL Wrapping Coating Tape

Our range of products include IWL Wrapping Coating Tape and Iwl Pypkote 2m Tar Based Pipe Coating Tapes.

IWL Wrapping Coating Tape
Interested in this product?
Get Best Quote

IWL Wrapping Coating Tape

Rs 230 / Square MeterGet Latest Price

Product Brochure

BrandIWL
TypeSingle Sided
Size1/2 inch
UsageFor Coating
Thickness4 mm +/- 10%
Tape Width1000 +/- 10 mm / 500 +/- 5 mm
Tape WeightMinimum 1.35 kg Per Sqm Per mm

Pypkote AW 4 mm is a Coal Tar Based Corrosion Protection Tape conforming to AWWAC 203 specification. It comprises of a Coal Tar based mix supported on a fabric of high tensile strength Fibreglass. The mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process. Application is fast and easy. The pipe surface is first cleaned with a wire brush. Resin based Synthetic Primer is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the synthetic primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the synthetic primer coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12.5 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover

View Complete Details

Yes, I am interested!

Iwl Pypkote 2m Tar Based Pipe Coating Tapes
Interested in this product?
Get Best Quote
Softening Point65 to 121 deg C,ASTM D-36
Thickness2 mm
Filler20 to 30%,IS 1217
Heat ResistanceDoes Not Drip at 100 deg C,ASTM D-146

Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.

View Complete Details

Yes, I am interested!
© Shellco (Regd.). All Rights Reserved (Terms of Use)