Shellco Registered

• Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-flowing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fillers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability. For larger repairs, the mixed Renderoc RG may be modified by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site. For exceptionally large repairs, the local Fosroc office shall be consulted.

• Renderoc RG is used for repairs to damaged reinforced concrete elements, particularly where access is restricted and where vibration of the placed material is difficult or impossible. It is suitable for various structural strengthening measures such as encasement build-ups, jacketing etc. 

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state. 
• Can be pumped or poured into restricted locations. 
• Highly fluid to allow for placement without vibration. 
• Pre-packed to overcome site-batched variations. 
• Rapid strength gain to facilitate early reinstatement.  
• High ultimate strengths and low permeability of cured repair. 
• Contains no chloride admixture. 

Dr. Fixit Pidifin 2K is a acrylic cementitious, polymer modified elastomeric, waterproofing & protective coating composed of best quality Portland cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. It is applied to waterproof and protect concrete and masonry substrates.

Areas of Application:

• Dr. Fixit Pidifin 2K must be applied to new or old concrete substrates that are structurally sound.
• Excellent as a waterproof coating for bathrooms, kitchen sinks, balconies, etc.
• Ideal as a coating for waterproofing of chhajjas, canopies, etc.
• As waterproof coating on internal sides of domestic water tanks.
• Good for waterproofing of sloped roofs.
• As a waterproof coating for terraces of areas up to 100-150 m2.

Features & Benefits:

• Elastomeric elastomeric flexible coating that accommodate cracks up to 2 mm with an elasticity of 40-50%
• Low water permeability excellent resistance to ingress of water
• Adhesion excellent adhesion to concrete and masonry surfaces
• Eco-friendly Non-toxic with low VOC content
• CFTRI certified as a “potable water safe” coating for waterproofing for water tanks

Method of Application:

• The surface of application must be thoroughly prepared by mechanical means, to remove all loose particles, laitance, etc.
• Oil and grease, if any, must be de-greased with suitable solvents. It then must be washed off with jet of water and brought to touch dry state. Any surface undulations, cracks and crevices must be duly filled or repaired with cement sand mortar mixed with latex polymers such as Dr. Fixit Pidicrete URP / Dr. Fixit Pidicrete MPB.

TECHOXY-3 is a two component epoxy resin based waterproofing compound. One part consists of epoxy resin and the other part of curing agent. After mixing both the parts, it can be thinned down with water. It possesses all the attributes of normal solvent based epoxy compositions such as excellent water and chemical resistance, adhesion, hardness, toughness and mechanical strength. One of the major advantages of Techoxy-3 over solvent based epoxy is that it can be applied on damp surface also. Being free from solvents, it does not pose any health hazard to the applicator. Techoxy-3 is completely, consistent & economical to apply.

Features/Advantages:

• Water dilutable
• Being water based, it penetrates in concrete/plaster surface and seals the porosity and network of fine cracks
• Reduces water permeability
• After curing it forms hard, tough and strong film
• Bonds strongly on cement concrete/mortar, plaster, asbestos sheet etc.
• Excellent resistance to water, salt water, dilute acids, alkalis, soap water, and other chemicals
• Excellent resistance to positive (hydrostatic) water pressure
• Eco friendly & non-toxic in nature

Application Areas:

• Cement-concrete water storage tanks
• Damp walls (interior / exterior )
• As a primer before painting (interior / exterior )
• As an undercoat before applying Techoat 61-P & Tar-o-Thane on roof terrace and internal walls.
• Toilet and kitchen walls
• Coating on walls of breweries & food processing industries
• As a primer before application of Techsterile-sterile coating in food & drug industries
• As a putty with OPC-white cement to fill the fine cracks of external walls
• Hatcheries & aqua farms

An acrylic polymer based economical elastomeric waterproofing system for protecting concrete & masonry surfaces.

Areas of Application:

• Concrete structures like sunken portion, toilets, balcony, basement, chajjahs, terrace, concrete repairs and water retaining structures.

Features & Benefits:

• A tough, hard wearing, breathable waterproofing system for residential, industrial, housing and commercial buildings.
• Can be applied in uniform thickness to horizontal and vertical surfaces.
• Excellent bond to most building materials.
• Reduces or prevents salt penetration into concrete.
• High ultra voilet resistance.
• Highly durable.
• Economical system.
• Is non-flammable and does not give off toxic gases, when exposed to fire.

Method of Application:

For waterproofing:

• Surface preparation: Prior to application of Dr. Fixit Powercrete, ensure to clean the substrate which should be free from all the dust, foreign particles, loose aggregate and oil grease etc. This can be done with the help of scarifying, grinding, water jetting and sand blasting etc.
• The surface should be wetted, well prior to application, thoroughly with water to get SSD condition.
• All the depression or pin holes /pot holes to be repaired using Dr. Fixit Powercrete modified mortar in mixing ratio of ( 1 kg cement : 1.50 kg silica sand : 0.50 kg of Dr. Fixit Powercrete )

Description:

• Dr. Fixit Fastflex is a two component cementitious coating, composed of high quality cement, properly selected & graded fillers, additives and liquid polymer. It is suitable for achieving waterproofing for the water retaining structures such as swimming pools, water tanks, reservoirs, other wet areas, etc, because it provides strong bonding, good waterproofing and provides excellent resistant to hydrostatic water pressure by forming highly elastic seamless coating over the applied concrete or masonry surfaces.

Areas of Application:

• Any concrete, cement or masonry surface that is subjected to damage from moisture.
• Swimming pools, water tanks and reservoirs.
• Concrete roofs, basements, and basement walls and lift pits.
• Concrete foundations.
• Parking decks.
• Bathrooms, toilets, sunken portions, balconies, planters, etc.
• Podiums.

Features & Benefits:

• Elasticity - Highly elastic film formation which accommodates thermal movements.
• Permeability - Impermeable to water providing excellent waterproofing property.
• Water pressure - High film built-up to withstand 10m hydrostatic pressure without any leakages.

• Can be applied on damp surfaces leading to wide range application and instant remedy from moisture.
• Bonding - Excellent adhesion to concrete and masonry substrates hence longer life.
• Drying - Quick drying after application & user friendly, faster application.
• Seamless coating – Forms seamless coating without any joints, prevents water leakage.
• Toxicity – It is Non-toxic and free of VOC.
• Ease of application - Easily applied by brush, roller or spray.

• Surface under treatment should be sound, clean and free from dirt, oil and other loose material
• Masonry surfaces should be fully cured (minimum 28 days) prior to application.
• All surface cracks, undulations and voids must be repaired appropriately before application
• Surface must be in SSD condition prior to application.

• Use slow speed mechanical mixer, add powder component slowly to the polymer in a clean container
• Stir till smooth and homogeneous slurry, without any lumps, is achieved
• Allow the mixed slurry to stand for 5-10 minutes for releasing trapped air during mixing.

Application:

• Do not dilute with water
• Apply Fastflex slurry by brush, roller or trowel.
• Allow the slurry to dry completely for 6-8 hrs before applying 2nd coat.

• Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation. Standard Compliance / Specification Meets the requirements of IS : 2645-2003 and IS: 9103-2000 standards

• Waterproofing of concrete and sand-cement mortars used in Basements
• Roof slabs and screeds
• Water tanks & water retaining structures
• External plastering
• Bathrooms and balconies
• Sumps and drains

• Corrosion resistant - Makes concrete more cohesive, hence protects steel better against corrosion
• Compatibility – Being a liquid, easily dispersible & compatible with concrete/mortar mixes.
• Permeability – It reduces the permeability of water into concrete.
• Strength – The setting time and compressive strength of the concrete remains within the specification limits.
• Shrinkage – Reduces shrinkage crack development in plaster & concrete.
• Workability – Improves workability of freshly mixed cement concrete.
• Durability – Increases durability by improving waterproofing of concrete.
• Method of Application
• Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes.
• Start addition of 75–80% mixing water & mix for 2-3 minutes.
• Dr. Fixit Pidiproof LW+ is added as per the recommended dosage into the remaining mixing / gauging water,
• then add to concrete mixer & mix for another 2 minutes.
• Place the concrete or apply plaster, as needed.
• Cure the applied mortar or concrete as per good construction practices.

• Do not add Dr. Fixit Pidiproof LW+ directly to dry cement & aggregate mix.
• Maintain water-cement ratio as low as possible.
• Do not increase the dosage of Dr. Fixit Pidiproof LW+ than the recommendation

Additional Information:

• Item Code: 101

• Chemical Resistance: Resist chemical attack (pH 3-11 constant contact, pH 2-12 intermittent contact) and provides a range of protection from freeze/ thaw cycles, aggressive subsoil waters, sea water, carbonates, chlorides, sulfates and nitrates.
• Application advantage: Does not require protective plaster, applicable over SSD & wet surface.
• Waterproofing: Stops water movement through concrete, becomes integral part of the structure.
• Corrosion: Protects reinforcing steel against corrosion.
• Sealing: Waterproofs minor cracking & seals shrinkage cracks up to 0.4 mm width.
• Permeability – Resists permeation of water from positive & negative side of the concrete.
• Chemical activation: It’s waterproofing capability increases with time. i.e. It remains permanently active.
• Abrasion: Does not get affected by surface wear or abrasion, once the penetration is complete.
• Hydrostatic pressure: Treated concrete withstands hydrostatic water pressure up to 15 metre head.
• Ease of application: Easy in application, only to be mixed with water at site.
• Protection: Protects concrete against contaminated water & corrosion.
• Monolithic: Forms monolithic layer with the concrete & becomes integral part of concrete.
• Crack bridging: Can bridge cracks upto 0.5 mm

• Water Retaining Structures 
• Water tanks & reservoirs 
• Swimming pools 
• Water treatment works 
• Dams & canals
• Concrete pipes 
• Harbours 

• Foundation & Basements 
• Tunnels, subways & stations 
• Inspection pits & lifts shafts 
• Retaining walls & sea defence walls 
• Construction joints
• Bridge decks
• Jetties 
• Parking structures

• Dr. Fixit Krystalline is composed of high quality cement, properly selected & graded inert aggregates, proprietary waterproofing active chemicals & additives. It is used as a chemically active waterproofing treatment for concrete. Dr. Fixit Krystalline when mixed with water and applied as a brush coat to concrete, it penetrates deeply into the capillaries of the concrete & protects it against the permeability of water. 

• Application advantage – Does not require protective plaster, applicable over SSD & wet surface.
• Waterproofing - Stops water movement through concrete, becomes integral part of the structure.
• Corrosion - Protects reinforcing steel against corrosion.
• Sealing - Waterproofs minor cracking & seals shrinkage cracks upto 0.4 mm width.
• Permeability – Resists permeation of water from positive & negative side of the concrete.
• Chemical activation -It’s waterproofing capability increases with time. i.e. It remains permanently active.
• Abrasion - Does not get affected by surface wear or abrasion, once the penetration is complete.
• Toxicity - Non toxic thus good for use in drinking water containments.
• Hydrostatic pressure -Treated concrete withstands hydrostatic water pressure upto 15 metre head.
• Ease of application - Easy in application, only to be mixed water at site.
• Protection - Protects concrete against contaminated water & corrosion.
• Breathability - It allows concrete to breath but is not a vapour barrier.
• Saving – Economical to apply than other waterproofing treatments. Expensive surface preparation, costly priming & levelling of the surface prior to application of Dr.Fixit Krystalline are not required.
• Monolithic – Forms monolithic layer with the concrete which cannot be punctured, teared & removed from the surface.

• The proprietary waterproofing active chemical plays very important role & it is a very simple reaction with the natural chemical byproducts of cement hydration, such as calcium hydroxide, various mineral oxides, hydrated & unhydrated cement particles of the concrete in wet condition. The result of chemical reaction is the formation of billions of needles like non-soluble crystals which block the pores of the capillaries, voids & micro-cracks in concrete. After blocking, the pores & capillary tracts of the concrete become discontinuous which stops the permeability from all directions of the treated concrete. Dr. Fixit Krystalline remains active whenever water is present. 
• Pre-saturation & subsequent re-wetting of the surface will cause diffusion of the organic chemicals & formation of crystals by reaction at greater depth. It may take from seven days to one month to reach its maximum waterproofing capability, depending on the thickness of the concrete. 
• Environmental factors such as ambient temperature, density of concrete, moisture presence & weather conditions can affect the timing of sealing process. Under dry conditions, Dr. Fixit Krystalline lies dormant. However it becomes reactive whenever it is re-exposed to moisture. 
• It penetrates even against strong hydrostatic pressure, becoming an integral part of the concrete. The waterproofing chemicals remain active for the life of the structure, permanently sealing it for water seepage. 

• Water Retaining Structures 
• Water tanks, towers & reservoirs. 
• Swimming pools. 
• Water treatment works. 
• Dams & canals. 
• Concrete pipes.
• Harbours. Water Excluding Structures 
• Foundation & Basements. 

Additional Information:

• Item Code: 107

• Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water.
• Brushbond RFX is suitable for all types of structures including those in coastal environments.
• The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures.
• The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks.
• It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications.

• Excellent barrier to carbon dioxide, chloride and sulphate ions.
• Allows water vapour to escape from the structure.
• Waterproof-suitable for water retaining structures.
• High resistance to the effect of long-term weathering, durable in all climate conditions including UV attack.
• Non toxic - ideal for potable water tanks.
• Flexible, with thermal expansion similar to concrete.
• Excellent bond to concrete and masonry.
• Good crack accommodation capacity.
• Minimum surface preparation needed and low labour costs.