SILVERLINE DISTRIBUTOR PRIVATE LIMITED

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils)

If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance.

The 10W6v3 is best used with amplifier power in the 200W – 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the “Specifications” tab.

Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver.

Summary:
JL Audio’s proprietary Dynamic Motor Analysis system is a powerful suite of FEA-based modeling systems, first developed by JL Audio in 1997 and refined over the years to scientifically address the issue of speaker motor linearity. This leads to vastly reduced distortion and faithfully reproduced transients… or put simply: tight, clean, articulate bass.

Detailed Information:
Since 1997, JL Audio has been at the forefront of Finite Element Analysis-based modeling of loudspeaker motors and suspensions. This research is aimed at decoding what we refer to as the “Loudspeaker Genome”… a project aimed at understanding the true behavior of loudspeakers under power and in motion. A major component of this integrated system is DMA (Dynamic Motor Analysis). Starting with the 15W3 and the W7 Subwoofers in the late 1990’s and early 2000’s, DMA has played an important role in the design of all JL Audio woofers sold today, including our component woofers.

DMA is a Finite Element Analysis (FEA)-based system, meaning that it takes a large, complex problem, breaks it down into small solution elements for analysis and then assembles the data to form an accurate, “big-picture” solution. DMA’s breakthrough is that it actually considers the effects of power through the coil as well as coil/cone position within the framework of a time-domain analysis. This gives us a highly accurate model of a speaker’s actual behavior under real power, something that the traditional Thiele-Small models or other low power measurements cannot do. Because DMA does not rely on a steady-state model, it is able to consider shifts in the circuit elements being analyzed. These modeling routines are intense, requiring hours to run for a whole speaker.

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)

If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance.

The 12W6v3 is best used with amplifier power in the 200W – 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the “Specifications” tab.

Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver.

Summary:
JL Audio’s proprietary Dynamic Motor Analysis system is a powerful suite of FEA-based modeling systems, first developed by JL Audio in 1997 and refined over the years to scientifically address the issue of speaker motor linearity. This leads to vastly reduced distortion and faithfully reproduced transients… or put simply: tight, clean, articulate bass.

Detailed Information:
Since 1997, JL Audio has been at the forefront of Finite Element Analysis-based modeling of loudspeaker motors and suspensions. This research is aimed at decoding what we refer to as the “Loudspeaker Genome”… a project aimed at understanding the true behavior of loudspeakers under power and in motion. A major component of this integrated system is DMA (Dynamic Motor Analysis). Starting with the 15W3 and the W7 Subwoofers in the late 1990’s and early 2000’s, DMA has played an important role in the design of all JL Audio woofers sold today, including our component woofers.

DMA is a Finite Element Analysis (FEA)-based system, meaning that it takes a large, complex problem, breaks it down into small solution elements for analysis and then assembles the data to form an accurate, “big-picture” solution. DMA’s breakthrough is that it actually considers the effects of power through the coil as well as coil/cone position within the framework of a time-domain analysis. This gives us a highly accurate model of a speaker’s actual behavior under real power, something that the traditional Thiele-Small models or other low power measurements cannot do. Because DMA does not rely on a steady-state model, it is able to consider shifts in the circuit elements being analyzed. These modeling routines are intense, requiring hours to run for a whole speaker.

W3v3 12-inch Subwoofer (500 W, 4 Ω)

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability.

The 12W3v3-4 is best used with amplifier power in the 150W – 500W range and is optimized to operate in a compact 1.125 cu. ft. (31.8 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Detailed enclosure recommendations can be found in the “Specifications” tab.

Summary:
JL Audio’s proprietary Dynamic Motor Analysis system is a powerful suite of FEA-based modeling systems, first developed by JL Audio in 1997 and refined over the years to scientifically address the issue of speaker motor linearity. This leads to vastly reduced distortion and faithfully reproduced transients… or put simply: tight, clean, articulate bass.

Detailed Information:
Since 1997, JL Audio has been at the forefront of Finite Element Analysis-based modeling of loudspeaker motors and suspensions. This research is aimed at decoding what we refer to as the “Loudspeaker Genome”… a project aimed at understanding the true behavior of loudspeakers under power and in motion. A major component of this integrated system is DMA (Dynamic Motor Analysis). Starting with the 15W3 and the W7 Subwoofers in the late 1990’s and early 2000’s, DMA has played an important role in the design of all JL Audio woofers sold today, including our component woofers.

DMA is a Finite Element Analysis (FEA)-based system, meaning that it takes a large, complex problem, breaks it down into small solution elements for analysis and then assembles the data to form an accurate, “big-picture” solution. DMA’s breakthrough is that it actually considers the effects of power through the coil as well as coil/cone position within the framework of a time-domain analysis. This gives us a highly accurate model of a speaker’s actual behavior under real power, something that the traditional Thiele-Small models or other low power measurements cannot do. Because DMA does not rely on a steady-state model, it is able to consider shifts in the circuit elements being analyzed. These modeling routines are intense, requiring hours to run for a whole speaker.

TW3 10-inch Subwoofer (400 W, dual 4 Ω voice coils)

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of greater excursion than the W3v3’s.

To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of the large motor structure further forward in the speaker than with conventional designs.

TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing Subwoofers.

Deep, powerful and accurate JL Audio bass is now possible in more applications than ever.

• Very shallow mounting depth (3.25 / 3.50 Inches)
• No pole vent: permits mounting close to rear wall of enclosure.
• Very small sealed enclosure volume requirements
• Very long linear excursion capability (0.60 In / 15.2 mm, one-way)
• DMA-optimized motor designs
• “concentric tube” architecture
• Patented “floating cone attach method” technology
• Cast alloy frame
• Injection molded, mica-filled polypropylene cone
• Rubber surround
• Aluminum-alloy dust cap and rear cap with JL Audio logo
• Precision-built in USA at JL Audio’s Miramar, Florida factory with global components

Summary:
JL Audio’s proprietary Dynamic Motor Analysis system is a powerful suite of FEA-based modeling systems, first developed by JL Audio in 1997 and refined over the years to scientifically address the issue of speaker motor linearity. This leads to vastly reduced distortion and faithfully reproduced transients… or put simply: tight, clean, articulate bass.

Detailed Information:
Since 1997, JL Audio has been at the forefront of Finite Element Analysis-based modeling of loudspeaker motors and suspensions. This research is aimed at decoding what we refer to as the “Loudspeaker Genome”… a project aimed at understanding the true behavior of loudspeakers under power and in motion. A major component of this integrated system is DMA (Dynamic Motor Analysis). Starting with the 15W3 and the W7 Subwoofers in the late 1990’s and early 2000’s, DMA has played an important role in the design of all JL Audio woofers sold today, including our component woofers.

DMA is a Finite Element Analysis (FEA)-based system, meaning that it takes a large, complex problem, breaks it down into small solution elements for analysis and then assembles the data to form an accurate, “big-picture” solution. DMA’s breakthrough is that it actually considers the effects of power through the coil as well as coil/cone position within the framework of a time-domain analysis. This gives us a highly accurate model of a speaker’s actual behavior under real power, something that the traditional Thiele-Small models or other low power measurements cannot do. Because DMA does not rely on a steady-state model, it is able to consider shifts in the circuit elements being analyzed. These modeling routines are intense, requiring hours to run for a whole speaker.

• 12" FXB Series Amplified Subwoofer Enclosure
• Power Output:
  • Peak: 500 watts
  • RMS: 300 watts
• Frequency Response: 40 - 500Hz
• Sensitivity: 93 dB
• System Impedance: 4-Ohm
• Dimensions: 14.75"D x 17"W x 15.25"H
• Authorized Internet Dealer
• 1-year Manufacturer's Warranty

• Built-In Crossover
• High Gloss Black Acrylic Piano Finish Cone
• Low Level RCA Input
• High Level Input
• Custom Logo Embroidery
• Laminated Butyl Rubber Surround
• 3D Injected Poly Dust Cap
• 4th Order Bass Reflex Ported Design

• Infinity Harman 1400T Primus 8 1400w Powered Subwoofer Bass Tube. 1400 Watts Peak/200 Watts RMS.
• Innovative materials and breakthrough engineering have always put Infinity products out in front of the competition. So expect extreme output from PRIMUS subs, but be prepared for accuracy and detail that may simply blow you away.
• The PRIMUS Series subwoofers feature SSI (Selectable Smart Impedance), a HARMAN-exclusive impedance selector, that lets you choose a 2- or 4-ohm impedance at the flip of a switch.
• Our proprietary aero-cooling design keeps the voice coil cool while optimizing power handling and long term reliability.
• The acoustically damped glass-fibre cones have been engineered to minimize distortion and unwanted artifacts. More performance. More flexibility. You get both when you step up to a PRIMUS subwoofer.
• 1 YEAR WARRANTY
• IN-BUILT AMPLIFIER : YES

Loud and powerful

The newly designed champion series pro subwoofers are built to produce loud and powerful bass capable of withstanding up to 2,000 watts of maximum power with 600 watts of continuous musical power.

Installation flexibility

Designed with dual 4 ohm voice coils, for an 8 ohm or 2 ohm configuration, these subwoofers are capable of fitting into a 0.85 cubic ft. to 1.75 cubic ft. Enclosure.

Design improvements

Improving on conventional designs, the ts-w3003d4 features a dual spider design for improved linearity, a larger pole with thicker wire for more accurate bass, a larger magnet for louder bass, and a reinforced basket for more durability.

Looking for more bass? Now connect more than one sub-woofer with increased installation options. Not convinced? This champion series sub-woofer also features a powerful cone design with dual voice coil & dual-layer surround to produce strong, rich bass.

The new IMPP composite cones are designed specifically to prevent cone failures at high sound pressure levels. Composite Cones have a well balanced rigidity and moves in unison without any strong or weak points.

The first of its kind technology, Dual-Layer Elastic Polymer Surround dramatically improves durability and lightness, for superior response, especially for louder volume.

For loudness & durability as compared to a single voice coil

To suppress undesirable sound-distorting recoil to the cone, realize clear and punchy bass sound

Copper offers less resistance & is crucial in clear sound reproduction

Car Audio Fanatics who want Rockford Fosgate quality can rely on the Prime Series 10″ subwoofers to get the job done, and the Dual Voice Coil provides awesome installation flexibility. These drivers can pump out the bass due to their mica injected polypropylene cone, and their stamp-cast baskets with spider venting – typically reserved for more expensive models – keep the motor running cool! These R2 subwoofers are optimized for sealed and vented enclosures.

• 12 AWG compression terminals
• Anodized aluminum voice coil former
• Optimized for both sealed and vented enclosures
• Mica injected polypropylene cone
• Linear spider with embedded 16 AWG tinsel leads
• StampCast basket with integrated spider venting
• Integrated PVC trim ring
• 1 Year Warranty

Rockford Fosgate Prime R1 12” subwoofers provide high performance bass at an unbelievable value. This model features a laser etched curvilinear dust-cap to dissipate heat generated by the high???temp copper voice coil as well as a solid stamped steel frame with integrated frame mounted compression terminals. Best of all, they are optimized for both sealed and vented enclosures.

• Fiber reinforced painted paper-pulp cone
• Laser-etched aluminum dustcap
• High durability compressed foam surround
• Fatigue resistant poly-cotton spider with integral woven leads
• Proprietary powder coated stamped steel frame with spider cavity venting
• Bumped backplate with vented pole piece for greater thermal/mechanical power handling
• High-temp copper voice coil with aluminum former
• High-grade Y30 Ferrite magnet
• Integrated spring-loaded nickel-plated push terminals
• Integrated ABS decorative trim ring
• 1 Year Warranty

Rockford Fosgate P1 15″ are the first in a family of world famous subwoofers called “The Punch”. During their inception in the 1980’s, they quickly became “The Woofer of Choice” for fanatic car audio systems, with a continued tradition today. Kevlar fiber reinforced paper cones deliver bass impact you can feel, and our VAST technology increases surface cone area up to 25%. Best in standard sealed and vented enclosures. Includes soft touch ABS trim ring.

• Linear spider with embedded 16 AWG tinsel leads
• High-temp voice coil with spun-laced Nomex® re-inforcement collar
• Kevlar fiber reinforced paper cone
• StampCast basket with integrated spider venting
• Rubberized ABS trim ring with optional grille
• Custom 10-AWG nickel plated push terminals
• Extended pole piece and bumped vented backplate
• Protective PVC textured magnet cover
• 1 Year Warranty
• IN-BUILT AMPLIFIER: No

Improved reliability and performance by reducing fatigue and possible shorting.

Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards

The slot mounted frame pattern allows fine-tuning of the subwoofer’s mounting position.

Klippel is a speaker certification program allowing us to deliver the best possible subwoofers.

Rockford Fosgate subwoofers use anodized aluminum voice coil formers that provide superior heat dissipation (up to 100° at full power levels). Unlike traditional plastic substitutions, aluminum acts like a heat-sink to quickly dissipate thermal build-up on the voice coil. This keeps subwoofers cool during high SPL conditions.

New Champion Series Subwoofer at 1600W maximum power

Dual layer, fiber reinforced elastic polymer surround. High heat resistance voice coil & Large magnet with high heat dissipation.

Rigid seamless structure cone and honeycomb design cap. Double stacked large magnets.

Heavy magnetic circuit and an optimised basket to hold it. Firmly enclosed bottom basket for accurate cone motion

With Class-D amplifier technology, the subwoofer generates 200W maximum power, consuming power at levels lower than conventional amplifier designs and reducing the need for a large, traditional heat sink. The result is a compact, easy to install amplifier which in some vehicles requires no direct battery connection. Selectable bass mode and Back-loaded horn technology bring you the best experience in the vehicle.

TS-WX70DA features two selectable Bass Modes: DEEP and DYNAMIC, producing strong, rich, deep bass you can feel. You can easily control and customize the bass output from the supplied wired remote control.
DEEP Mode: Achieve rich, deep bass sound quality in the car. Suitable for Classic, Jazz, Country Music, etc. DYNAMIC Mode: Emphasize powerful, strong and dynamic bass sound in the car. Suitable for EDM, Hip-Hop, Rock Music, etc.

This unique structure reduces the mechanical resistance and reproduces a natural & deep bass sound effectively.

Thanks to its solid body, it can be installed freely in the luggage area for optimal utilisation of space.

Newly adopted CLASS-D technology realizes low power consumption and direct connection to the car battery is not necessary.

The most convenient way to get low frequency bass in your system is to drop-in a Punch Loaded enclosure. We’re not talking junk in the trunk, we’re talking the same genuine Punch woofers available separately. Punch Loaded enclosures are constructed with durable 5/8″ MDF and tuned by our computer aided design software. P1 Loaded Enclosures feature similar tonal performance as P2/P3 models, but are easier to move in-n-out of vehicles due to their lighter weight.

• Constructed with 5/8″ MDF
• Proprietary high-flow, low-noise port
• High current binding posts
• 1 Year Warranty

Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards.

Klippel is a speaker certification program allowing us to deliver the best possible subwoofers.

The P3D4-12 12-inch subwoofer is Rockford Fosgate’s best performing Punch series subwoofer. The P3 subwoofers now feature anodized aluminum cones and dustcaps along with unique spider venting to keep the motor cooler than previous versions. These feature VAST technology to increase surface cone area up to 25% and a FlexFit basket for extreme installations. Best of all, a new hybrid stamp-cast basket offers the best of both worlds by providing super strength while minimizing weight and resonance.

• Custom 10-AWG nickel plated push terminals
• Dual linear spider with embedded 16 AWG tinsel leads
• Extended pole piece and bumped vented backplate
• High-temp voice coil with spun-laced Nomex® re-inforcement collar
• Anodized aluminum cone and dustcap
• Protective PVC textured magnet cover
• Diamond cut cast aluminum trim ring with optional grille
• StampCast basket with integrated spider venting
• 1 Year Warranty
• In-Built Amplifier: No

Improved reliability and performance by reducing fatigue and possible shorting.

Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards.

The Vertical Attach Surround Technique significantly increases a subwoofer’s effective radiating cone area up to 25%.

Klippel is a speaker certification program allowing us to deliver the best possible subwoofers.

Rockford Fosgate subwoofers use anodized aluminum voice coil formers that provide superior heat dissipation (up to 100° at full power levels). Unlike traditional plastic substitutions, aluminum acts like a heat-sink to quickly dissipate thermal build-up on the voice coil. This keeps subwoofers cool during high SPL conditions.

The slot mounted frame pattern allows fine-tuning of the subwoofer’s mounting position.

When you have no space for bass, our PRIME R2S 12″ shallow loaded enclosure is sure to be a perfect fit for your ride and your budget. These shallow loaded enclosures can fit in tight spaces due to the slim-line depth of 3.25″ on the top and 5.25″ on the bottom. The wedge design is optimized for single-cab trucks with limited seat travel. Are you ready to rock out? Yeah, we thought so.

• Constructed with 5/8″ MDF
• Covered with high density carpet
• High current binding posts
• 1 Year Warranty

When you have no space for bass, our R2 12″ shallow subwoofer can help satisfy your need for low frequency music. These drivers can fit in tight spaces due to an elevated motor structure that reduces speaker depth. Mica injected polypropylene cones make sure bass notes are clean and accurate. Stamp-cast baskets feature spider venting typically reserved for traditional depth mounted models to keep the motor cool! These shallow subwoofers are optimized for sealed enclosures.

• 12 AWG compression terminals
• Anodized aluminum voice coil former
• Optimized for sealed enclosures
• Mica injected polypropylene cone
• Linear spider with embedded 16 AWG tinsel leads
• StampCast basket with integrated spider venting
• Integrated PVC trim ring
• Shallow Motor Assembly
• 1 Year Warranty

If you need to quickly add bass to a system or want to alleviate the hassle of separate amplifiers and subwoofers, then the P300-10 is the right one for the job! The P300-10 features a Punch 10” subwoofer in a custom sealed enclosure and is powered by a mighty 300 Watt amplifier. The system is all-inclusive, so you only need to run power, ground and a signal from the source to get this baby moving. Features a durable exterior that resists scrapes and bumps while in the trunk or cargo area.

• “Closed-loop” design ensures optimum performance between woofer, amplifier and enclosure
• Built-in 0°/180° phase switch
• Separate low level and speaker level inputs
• Built-in adjustable bass boost EQ
• Adjustable 12db/Octave low pass crossover
• Detachable Power/Ground connector
• Intelligent auto turn on/off function
• Thermal and over/under voltage protection
• High-efficiency, low current design
• Remote bass level control included
• Proprietary high output woofer
• Constructed with 5/8″ MDF
• Large AWG input terminals
• Covered with industrial heat activated vinyl
• 1 Year Warranty
• In-Built Amplifier: No

Power handling on Rockford Fosgate speakers conform to CEA-2031 industry standards.

Power ratings on Rockford Fosgate amplifiers conform to CEA-2006 industry standards

Klippel is a speaker certification program allowing us to deliver the best possible subwoofers.