Unicon Instruments

Overview:

The DIGITAL LAB is intended for elementary as well as advance training of digital electronics. The digital lab covers regular digital circuits by solder-less interconnections on breadboard and as well as compatible with all optional modules through use of 2mm brass terminals and patch cords. Various clock generators, logic level input/output indicators and DC regulated power supplies etc. are in-built. The unit housed in attractive enclosure is supplied with mains cord, patch cords, Instruction manual and Component Set.

Techincal Discription:

Bread Board : Unique solder-less large size, spring loaded breadboard consisting of two Terminal Strips with 1280 tie points and 4 Distribution Strips with 100 tie points each, totaling to 1680 tie points. (Size : 112mm x 170mm approx)

Regulated DC Power Supply :  5V at 1 Amp, -5V at 500 mA, 3 to 15V at 500mA, and -3 to -15V at 500 mA.

Pulse Generator : 1 Hz to 100 KHz in 6 Steps. Variable in between steps

- Amplitude : 3-15V (CMOS), 5V (TTL)

- Duty Cycle : 50% TTL / CMOS Output

Pulsar Switches : 1 independent buffered bounce free manual pulser (useful for freezing the action of each stage of the counter after every clock pulse)

Data Switches : 12 Nos. independent buffered logic level inputs to select High / Low TTL levels, each with a bi-color LED to indicate high / low status and termination.

Logic Indicators : 12 Nos. independent buffered logic level indicators for High / Low status indication with bi-color LED for digital outputs

Seven Segment Display : 2 Nos. BCD to Seven Segment Decoder / Driver IC with terminals

Logic Probe : Logic level indicator for TTL / CMOS

CMOS/TTL : Provided

Power : 230 V ± 10%, 50 Hz

Components Provided : ICs-4001/1, 4049/1,4069/1, 7400/1, 7402/1, 7404/1, 7406/1, 7408/2, 7410/2, 7411/3, 7420/2,7432/3, 7474/2,7476/2,7486/1.Resistors-330E/1,1K/2, 1K8/1,,15K/1, 47K/1.1M/2, Capacitors- 0.01mF/1, 0.1mF/1, 0.22 mF/1,Crystal-32.768MHz/1.

Accessories : Mains cord, Operating and Experimental manual, Red & Black patch cords (2mm with Pin) 10 each, Red & Black patch cord (Pin to Pin) 10 each. Wire 24/25 SWG. 1Meter each 5 Colour Instruction manual : Strongly supported by detailed operating instructions.

Additional Information:

• Item Code: UNICON-D244

COMPONENT DEVLOPMENT BREAD BOARD SYSTEM TRAINER

Specifications:

· 850 points bread board 1nos.

· Power supply 5V, 500mA is available in the trainer to use various TTL & CMOS ICs.

· On board pulsar circuit to provide the mono-pulse to the digital circuits.

· On board clock circuit to provide the low frequency clock to the digital circuits.

· 8 digital input logic high low switch.

· 8 digital output indicators.

· 20 pin zip sockets to place the various ICs and easily perform of the experiments with single chip integrated circuits.

· One 4 bit BCD To 7 Segment indicator to show decimal digit directly in case of counters.

· 2 mm sockets to make connections via 2mm patch cords.

Features

1. ‘UNICON’ Trainer operated on 230V, 50 Hz 10%

2. Supplied with instruction manual

3. Supplied with sufficient nos. of patch cords

4. Supplied with Computer Lead

5. Dimensions of the Trainer will be 12’’x10’’ with Plastic Box Highly shock proof .

Additional Information:

• Item Code: UNICON-D245

DIGITAL ELECTRONICS TRAINER 

The Digital Electronic Trainer is intended for elementary as well as advance training of digital electronics. The trainer covers regular digital circuits by solder less inter connections through use of 2 mm brass terminations and patch cords. Various clock generators, logic level input / output indicators and DC regulated power supply are in built. The unit housed in sun mica finished wooden box enclosure with provision for safe keeping of mains cord, patch cords and top lid for protection during storage.

Feature:

·         Breadboards: Unique solder - less large size, spring loaded breadboard consisting of one Terminal Strips with 640 tie points each and 2 Distribution Strips with 100 tie points each, totaling to 840 tie points. (Size: 55mm X 170mm approx ).

·         DC Power Supply: 5 V ± 0.25V / 500 mA (IC based regulated output).

·         Clock Generators: i) Fixed: a. 0.1Hz b. 1Hz. (Simultaneous independent outputs).

·         (TTL, 5V) : ii) Variable: One low frequency variable clock generator.

·         Manual Pulser : One independent bounce less manual Pulser ( useful for freezing the action of each stage of the counter after every clock pulse ).

·         Logic Level Inputs : Eight independent logic level inputs to select High / Low TTL levels, each with a LED to indicate high / low status and termination.

·         Logic Level : Eight independent buffered logic level indicators for High / Low status

·         Indicators : indication of digital outputs.

·         Seven segment decoder : One BCD to Seven Segment Decoder/ Driver IC with terminations.

·         Continuity Tester : Audio / Visual indication.

·         ZIF socket : IC’s up to 40 pin Universal ZIF Socket ( without soldering)

·         Potentiometer: One Potentiometer ( 100K ) with terminations.

·         Power On : Power ON switch with indicator for mains on indication and fuse for protection.

·         Patch Cords : Set of 20 assorted colored multi-stand wires with 2mm stackable plug termination at both ends.( Stackable )

·         Power Requirement : 230V  10% single phase AC.

·         Instruction manual : One detailed instruction manual with well thought out experiments covering the above topics

Additional Information:

• Item Code: UNICON-D241

DETERMINATION OF ENERGY BAND GAP IN SEMICONDUCTOR DIODE

Experimental Training Board has been designed specifically for Determination of Energy Band Gap in Semiconductor (P-N Junction Diode) using Temperature dependent of reverse saturation current.

Objective:
01. To draw the characteristics of a P-N junction Diode for reverse saturation current and temperature.
02. To determine the Energy Band Gap in a P-N Junction Diode.

Features:
The board consists of the following built-in parts :
01. 2V D.C. at 10mA, regulated Power Supply.
02. Digital Micro ammeter, 3½ digits having range 200uA D.C.
03. Semiconductor Diode.
04. Thermometer 0-110 °C.
05. Oven, Electrically heated to heat the Semiconductor Diode.
06. Mains ON/OFF switch and Fuse.
* The unit is operative on 230V ±10% at 50Hz A.C. Mains.
* Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug length ½ metre.
* Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections /observation of waveforms.
* Strongly supported by detailed Operating Instructions.

Additional Information:

• Item Code: UNICON-D240

ZENER DIODE CHARATERISTICS TRAINER WITH 4 METERS 

TRAINER USED TO STUDY THE FORWARD AND REVERSED BIASED CHARACTERISTICS.

• Kit comprises of 4 Meters (MR-65) Rectangle Type Voltmeter 15V and Ammeter of 250uA/25mA.
• Built in regulated power supply 0-5V/150mA, 0-15V/150mA required for forward and reverse characteristics.
• 3 different values of Zener connected on the panel via 4mm sockets.
• Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.
• Operated on Mains power 230V, 50Hz.
• Accessories: Required numbers of Patch Cords, Operating Manual and Computer Lead for Power Connection.

Optional: Trainer Kit Available in Digital Meters and Round Meters

Additional Information:

• Item Code: UNICON-D238

ANALOG AND DIGITAL TRAINER

Additional Information:

• Item Code: UNICON-D246

·        850 points bread board  1nos.

·        DC Power supplies 5V, 500mA and  12V, 250mA ar available in the trainer to use various TTL & CMOS ICs.

·        0-5V DC, with 250mA and 0-12V DC with 250mA are on board provided.

·        15-0-15VAC is provided on Board.

·        On board 0-250KHz Function Generator is provided to the digital circuits with Sine, Square and Triangle wave and with Variable amplitude and Frequency.

·        Two Nos. Digital Meters are provided on board for Voltage and Current readout.

·        One Frequency Counter is provided for Function Generator Frequency readout.

·        On board clock circuit to provide the low frequency clock to the digital circuits.

·        8 digital input logic high low switch.

·        8 digital output indicators.

·        2 mm sockets to make connections via 2mm patch cords.

Features

·        Trainer operated on 230V, 50 Hz   10%

·        Supplied with instruction manual

·        Supplied with sufficient nos. of patch cords

·        Supplied with Computer Lead

·        Dimensions of  the Trainer will be 12’’x10’’ with Plastic Box Highly shock proof .

Additional Information:

• Item Code: UNICON-D248

ANALOG AND DIGITAL BREAD BOARD TRAINER 

Additional Information:

• Item Code: UNICON-D247

UNIVERSAL BREAD BOARD SYSTEM TRAINER

Specifications:

· 850 points bread board 1nos.

· Power supply 5V, 500mA is available in the trainer to use various TTL & CMOS ICs.

· On board pulsar circuit to provide the mono-pulse to the digital circuits.

· On board clock circuit to provide the low frequency clock to the digital circuits.

· 8 digital input logic high low switch.

· 8 digital output indicators.

· 20 pin zip sockets to place the various ICs and easily perform of the experiments with single chip integrated circuits.

· One 4 bit BCD To 7 Segment indicator to show decimal digit directly in case of counters.

· 2 mm sockets to make connections via 2mm patch cords.

Features

· Trainer operated on 230V, 50 Hz 10%

· Supplied with instruction manual

· Supplied with sufficient nos. of patch cords

· Supplied with Computer Lead

· Dimensions of the Trainer will be 12’’x10’’ with Plastic Box Highly shock proof .

Experiments

· Study and verify Truth tables of Logic Gates.

· Verification of Boolean identities & Demorgan's theorems.

· Study and verify truth tables of Digital Adders & Subtractor.

· Study of Flip-Flops and verification of their truth tables.

· Study of Counters, Shift Registers and Verification of their truth tables.

· Study of Encoders, Decoders and Verification of their truth tables.

· Study of Multiplexers, Demultiplexer and verification of their truth tables.

· OP AMP experiments

· 555 experiments with additional components.

Additional Information:

• Item Code: UNICON-D249

POWER PROJECT BOARD TRAINER

POWER PROJECT BOARD –

it is specially designed for the doing experiments in digital electronics lab, where integrated circuits (ICS) are easily available. Students can easily perform experiments on this trainer.

It is versatile & economic trainer to perform analog and digital lab experiment on the bread board. The OP-AMP based experiments, digital logic gates experiment, flip flops, multivibrators, 555 timer experiment, adder and subtractor can be easily performed on this trainer board.

SPECIFICATIONS:

Ø     Two number of 950 points bread board.

Ø     Power supply 5V, 1A is available in the trainer to use with various TTL & CMOS ICs.

Ø     Power supply -5V, 250mA is available in the trainer to use with other experiments.

Ø     Variable Power supply 0 to 15V, 500mA is also available in the trainer to use with various 555 and OP-AMP. Experiments.

Ø     Variable Power supply 0 to -15V, 500mA is also available in the trainer to use with other experiments where needed.

Ø     2 mm sockets to make connections via 2mm patch cords.

Additional Information:

• Item Code: UNICON-D250

FLIP- FLOP TRAINER USING NAND GATES AND TTL IC’S

Computer Logic Training Board on Flip-Flops has been specifically designed to give students an idea about Flip- Flops and to study different types of Flip-Flops. The output of the Flip-Flops can be observed with the help of logic level indicators (LEDs), which are provided on the panel. The board is absolutely self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students.

Object:

To construct the following Flip-Flops and study their characteristics

Features
The board consists of the following built-in parts :
1. 5V D.C. at 100mA, IC regulated power supply.

2. Four Input Switches for data input.
 3. Eight, 2-input NAND gates.
4.  Four, 3-input NAND gates.
5. One inverter (NOT gate). 

7.  One 7476 IC Provided on board for JK and T type Flip Flop.

8. One 7474 IC Provided on the board for D Type Flip Flop.
9. Two LEDs with driver circuit to observe the output of flip-flops.

10. A Pulser to provide the pulses manually for triggering.

11. Adequate no. of other Electronic Components.
12. Mains ON/OFF switch, Fuse and Jewel light.

• The unit is operative on 230V ±10% at 50Hz A.C. Mains.
• Adequate nos. of patch cords stackable from rear both ends 4mm spring loaded plug, length ½ metre
• Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections / observation of waveforms.
•  Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
•  Weight : 2 Kg. (Approx.).
•  Dimension : W 300 x H 110 x D 200

Note: Specifications are subject to change. 

Additional Information:

• Item Code: UNICON-D251

MULTIPLEXER AND DEMULTIPLEXER TRAINER

Computer Logic Training Board on Multiplexer-Demultiplexer has been specifically designed to give students an idea about Multiplexer-Demultiplexer and to study of Multiplexer-Demultiplexer. The output of the Multiplexer-Demultiplexer can be observed with the help of logic level indicators (LEDs), which are provided on the panel. The board is absolutely self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students.

To construct the following Mux-Demux and study their characteristics

Features
The board consists of the following built-in parts :
1. 5V D.C. at 100mA, IC regulated power supply.

2. 21 Input Switches for data input.

3. IC For Multiplexing 74150 is provided on board with Combinational Circuit.

4. IC For Demultiplexing 74154 is provided on board with Combinational Circuit.

5. One Not Gate is provided on board using 7404
 6. 16 Output LEDs with driver circuit to observe the output of Multiplexer-Demultiplexer.

7. A Pulser to provide the pulses manually for triggering.

8. Adequate no. of other Electronic Components.
9. Mains ON/OFF switch, Fuse and Jewel light.

• The unit is operative on 230V ±10% at 50Hz A.C. Mains.
• Adequate nos. of patch cords stackable from rear both ends 4mm spring loaded plug, length ½ metre
• Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections / observation of waveforms.
•  Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
•  Weight : 2 Kg. (Approx.).

Additional Information:

• Item Code: UNICON-D252

SYNCHRONOUS AND ASYNCHRONOUS COUNTER TRAINER

Computer Logic Training Board on Synchronous and Asynchronous Counter has been specifically designed to give students an idea about Synchronous and Asynchronous Counter and to study of Synchronous and Asynchronous Counter. The output of the Synchronous and Asynchronous Counter can be observed with the help of logic level indicators (LEDs), which are provided on the panel. The board is absolutely self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students.

To construct the following Synchronous and Asynchronous Counter and study their characteristics :

Features

The board consists of the following built-in parts :
1. 5V D.C. at 100mA, IC regulated power supply.

2. 4 Nos. Input Switches for data input.

3. IC For Synchronous Counter 74193 is provided on board with Combinational Circuit.

4.  IC For Asynchronous Counter 74190 is provided on board with Combinational Circuit.

5.  Two 2 Input Or Gate is provided on board using 7432

6. Four 2 Input And Gate is provided on board using 7408

7. One 3 Input Nand Gate is provided on board using 7410

8. Two 3 Input And Gate is provided on board using 7411

9. Four JK Flip- Flop are provided using 7476 IC.
10. 5 Output LEDs with driver circuit to observe the Output .

11. A Pulser to provide the pulses manually for triggering.

12. Adequate no. of other Electronic Components.
13. Mains ON/OFF switch, Fuse and Jewel light.

• The unit is operative on 230V ±10% at 50Hz A.C. Mains.
• Adequate nos. of patch cords stackable from rear both ends 4mm spring loaded plug, length ½ metre
• Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections / observation of waveforms.
•  Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
•  Weight : 2 Kg. (Approx.).
•  Dimension : W 300 x H 110 x D 200

Note: Specifications are subject to change.

Additional Information:

• Item Code: UNICON-D253

ENCODER-DECODER TRAINER

Computer Logic Training Board on encoder-decoder has been specifically designed to give students an idea about encoder-decoder and to study of encoder-decoder The output of the encoder-decoder can be observed with the help of logic level indicators (LEDs), which are provided on the panel. The board is absolutely self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students.

Features
The board consists of the following built-in parts :
1. 5V D.C. at 100mA, IC regulated power supply.

2. 10 Nos. Input Switches for data input.

3. IC For BCD to 7 Segment Decoder 7447 is provided on board with Combinational Circuit.

4. IC For Decimal to BCD Encoder 74147 is provided on board with Combinational Circuit.

5. Binary to Grey Code using 7486 is provided with circuit diagram
6. 10 Nos. Output LEDs with driver circuit to observe the Output.

7. Seven Segment LT542 is provided on board.

8. Adequate no. of other Electronic Components.
 9.  Mains ON/OFF switch, Fuse and Jewel light.

• The unit is operative on 230V ±10% at 50Hz A.C. Mains.
• Adequate nos. of patch cords stackable from rear both ends 4mm spring loaded plug, length ½ metre
• Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections / observation of waveforms.
•  Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
•  Weight : 2 Kg. (Approx.).
•  Dimension : W 300 x H 110 x D 200

Additional Information:

• Item Code: UNICON-D254

DIGITAL LOGIC TRAINER

The Digital Logic Trainer is intended for elementary as well as advance training of digital electronics. The trainer covers regular digital circuits by solder less inter connections through use of 2 mm brass terminations and patch cords. Various clock generators, logic level input / output indicators and DC regulated power supply are in built. The unit housed in sun mica finished wooden box enclosure with provision for safe keeping of mains cord, patch cords and top lid for protection during storage.

Feature:

·         Breadboards: Unique solder -less large size, spring loaded breadboard consisting of one Terminal Strips with 640 tie points each and 2 Distribution Strips with 100 tie points each, totaling to 840 tie points. (Size: 55mm X 170mm approx ).

·         DC Power Supply: 5 V ± 0.25V / 500 mA (IC based regulated output).

·         Clock Generators: i) Fixed: a. 0.1Hz b. 1Hz. (Simultaneous independent outputs).

·         (TTL, 5V) : ii) Variable: One low frequency variable clock generator.

·         Manual Pulser : One independent bounce less manual Pulser ( useful for freezing the action of each stage of the counter after every clock pulse ).

·         Logic Level Inputs : Eight independent logic level inputs to select High / Low TTL levels, each with a LED to indicate high / low status and termination.

·         Logic Level : Eight independent buffered logic level indicators for High / Low status

·         Indicators : indication of digital outputs.

·         Seven segment decoder : One BCD to Seven Segment Decoder/ Driver IC with terminations.

·         Continuity Tester : Audio / Visual indication.

·         ZIF socket : IC’s up to 40 pin Universal ZIF Socket ( without soldering)

·         Potentiometer: One Potentiometer ( 100K ) with terminations.

·         Power On : Power ON switch with indicator for mains on indication and fuse for protection.

·         Patch Cords : Set of 20 assorted colored multi-stand wires with 2mm stackable plug termination at both ends.( Stackable )

·         Power Requirement : 230V  10% single phase AC.

·         Instruction manual : One detailed instruction manual with well thought out experiments covering the above topics 

Additional Information:

• Item Code: UNICON-D255

DIGITAL IC TRAINER

The Digital IC Trainer is intended for elementary as well as advance training of digital electronics. The trainer covers regular digital circuits by solder less inter connections through use of 2 mm brass terminations and patch cords. Various clock generators, logic level input / output indicators and DC regulated power supply are in built. The unit housed in sun mica finished wooden box enclosure with provision for safe keeping of mains cord, patch cords and top lid for protection during storage.

Feature:

·         DC Power Supply: 5 V ± 0.25% / 500 mA (IC based regulated output).

·         Clock Generators: i) Fixed: a. 0.1Hz b. 1Hz. (Simultaneous independent outputs).

·         (TTL, 5V) : ii) Variable: One low frequency variable clock generator.

·         Manual Pulser : One independent bounce less manual Pulser ( useful for freezing the action of each stage of the counter after every clock pulse ).

·         Logic Level Inputs : Eight independent logic level inputs to select High / Low TTL levels, each with a LED to indicate high / low status and termination.

·         Logic Level : Eight independent buffered logic level indicators for High / Low status

·         Indicators : indication of digital outputs.

·         Seven segment decoder : One BCD to Seven Segment Decoder/ Driver IC with terminations.

·         Continuity Tester : Audio / Visual indication.

·         ZIF socket : IC’s up to 40 pin Universal ZIF Socket ( without soldering)

·         Power On : Power ON switch with indicator for mains on indication and fuse for protection.

·         Patch Cords : Set of 20 assorted colored multi-stand wires with 2mm stackable plug termination at both ends.( Stackable )

·         Power Requirement : 230V  10% single phase AC.

·         Instruction manual : One detailed instruction manual with well thought out experiments covering the above topics

Additional Information:

• Item Code: UNICON-D256

4BIT SHIFT REGISTER TRAINER

Computer Logic Training Board on 4bit shift register trainer has been specifically designed to give students an idea about 4bit shift register trainer and to study of 4bit shift register trainer The output of the 4bit shift register trainer can be observed with the help of logic level indicators (LEDs), which are provided on the panel. The board is absolutely self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students.

Features
The board consists of the following built-in parts :
1. 5V D.C. at 100mA, IC regulated power supply.

·          2. 10 Nos. Input Switches for data input.

·          3. IC For Universal Shift Register 74194 is provided on board with Combinational Circuit.

·          4. IC For Parallel Shift register 7495  is provided on board with Combinational Circuit.

·          5. IC For Parallel-Serial Shift Register Using 7494 is provided with circuit diagram
6. 5. Nos. Output LEDs with driver circuit to observe the Output.

·          7. One Mono Pulse is provided on board.

·          8. Adequate no. of other Electronic Components.
 9.  Mains ON/OFF switch, Fuse and Jewel light.

• The unit is operative on 230V ±10% at 50Hz A.C. Mains.
• Adequate nos. of patch cords stackable from rear both ends 4mm spring loaded plug, length ½ metre
• Good Quality, reliable terminal/sockets are provided at appropriate places on panel for connections / observation of waveforms.
•  Strongly supported by detailed Operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References.
•  Weight : 2 Kg. (Approx.).
•  Dimension : W 300 x H 110 x D 200

Note: Specifications are subject to change. 

Additional Information:

• Item Code: UNICON-D257

UNIVERSAL SHIFT REGISTER USING CMOS IC

 OBJECTIVE: To study & verify truth table of Universal Shift Register using CMOS IC.

 FEATURES :

 Instrument comprises of DC Regulated Power Supply 5VDC/150Ma.

8 SPDT switches provided for selecting logic ‘1’ & logic ‘0’.

1Hz monoshot clock pulse.

Four output indicators.

Circuit diagram for IC 4035 printed.

Two switches for serial input & Mode control.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Size: 12’’x8’’

Additional Information:

• Item Code: UNICON-D258

DIVIDE BY 60 SYNCHRONOUS COUNTER USING 74190

OBJECTIVE: To study & verify truth table of Divide by 60 Synchronous Counter Using 74190

FEATURES :

 'UNICON' Instrument comprises of DC Regulated Power Supply 5VDC/150Ma.

5 SPDT switches provided for selecting logic ‘1’ & logic ‘0’.

2 Synchronous Counter Using 74190 are provided on board.

2 Not Gate Using 7404 are on board provided.

2 Nand gate are provided on board.

1Hz monoshot clock pulse.

6 output indicators.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Size: 12’’x8’’ 

Additional Information:

• Item Code: UNICON-D259

DIVIDE BY 100 SYNCHRONOUS COUNTER USING 4017

OBJECTIVE: To study & verify truth table of Divide by 100 Counter Using 74190

FEATURES :

'UNICON' Instrument comprises of DC Regulated Power Supply 5VDC/150Ma.

2 SPDT switches provided for selecting logic ‘1’ & logic ‘0’.

2  Synchronous Counter Using 4017 are provided on board.

1Hz monoshot clock pulse.

11 output indicators.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Size: 12’’x8’’ 

Additional Information:

• Item Code: UNICON-D260

PSEUDO RANDOM BINARY SEQUENCE GENERATOR TRAINER

OBJECTIVE: To Generate Pseudo Random Binary Sequence.

FEATURES :

'UNICON' Instrument comprises of DC Regulated Power Supply 5VDC/150Ma.

Mono pulse circuit is on the circuit.

Clock circuit is on the circuit.

4 Nos Output indicators.

Circuit diagram for Parity Generator and Parity Checker is Printed.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Size: 12’’x8’’ 

Additional Information:

• Item Code: UNICON-D261

DIGITAL IC LAB TRAINER

Which Perform (And, Or, Not, Nand, Nor, Xor, X-Nor, Counter, Flip-Flop, Register, Multiplexer, Demultiplexer Practical’s) - Features: The board consists of the following built-in parts:

01. + 5V D.C. at 1Amp, IC Regulated Power Supply Internally connected.

02. Five, J-K master slave flip-flops with preset and clear arrangement.

03. Six, 2-input NAND gates. 04. Four, 4-input NAND gates.

05. Three, 4-input AND-OR gates. 06. Two inverters (NOT gates).

07. A 4-bit binary counter to demonstrate the basic principles of frequency measurement.

08. A square wave oscillator of frequency 10 Hz, 1 KHz and 10 KHz with coarse and fine variations, demonstrate the basic principle of frequency division.

09. Completely programmable panel to make any type of counter or shift register.

10. Two Pulser switches for clear and clock arrangement.

11. One Mono Pulser to give a 1 sec pulse.

12. Three Band switches for various interconnections required in the circuit to provide greater convenience and avoiding wrong connections.

13. Two, 7-segment displays to monitor the output in decimal code.

14. LEDs for visual indication of output status of each flip-flop.

15. Adequate no. of other Electronic Components.

16. Mains ON/OFF switch, Fuse and Jewel light.

* The unit is operative on 230V ±10% at 50Hz A.C. Mains.* Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug length ½ meter.

Additional Information:

• Item Code: UNICON-D243

TRANSIENT RESPONSE IN RLC CIRCUIT TRAINER

Object: 

·        study the transient response of a series RC/RL circuit and understand the time constant concept with DC power supply

·        study the transient response of a series RC/RL circuit with Inbuild Square Wave generator

Special Feature:

·        On board DC Regulated Power Supply 5V at 250mA.

·        On board Square Wave Generator.

·        On Board RL and RC Circuit Provided With Circuit Diagram.

·        Components are mounted behind the panel

·        Adequate no. of patch cords stackable from rear both ends 4mm spring loaded plug length ½ meter

·        Good quality, reliable terminal/sockets are provided at appropriate places on panel for connections/ observation of waveforms

·        Trainer is housed in highly shockproof  plastic box having size of 12x8 inches.

·        Strongly supported by detailed operating instructions manual.

Additional Information:

• Item Code: UNICON-D239

ZENER DIODE CHARATERISTICS TRAINER

TRAINER USED TO STUDY THE FORWARD AND REVERSED BIASED CHARACTERISTICS.

• Kit comprises of 2 Meters Digital Type Voltmeter 15V and Ammeter of 250uA/25mA.
• Built in regulated power supply 0-15V required for forward and reverse characteristics.
• 3 different values of Zener connected on the panel via 4mm sockets.
• Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.
• Operated on Mains power 230V, 50Hz.
• Accessories: Required numbers of Patch Cords, Operating Manual and Computer Lead for Power Connection.

Optional: Trainer Kit Available in Square Meters and Round Meters

Additional Information:

• Item Code: UNICON-D237

ZENER DIODE AS VOLTAGE REGULATOR TRAINER

FEATURES:

• Kit comprises of 2 Meters (MR-65) Rectangle Type/Digital Voltmeter 25V and Ammeter of 100mA.
• Built in regulated power supply 0-25V/150mA required for forward and reverse.
• 3 different values of Zener connected on the panel via 4mm sockets.
• Fixed load resistor mounted on the panel.
• Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.
• Operated on Mains power 230V, 50Hz.
• Accessories: Required numbers of Patch Cords, Operating Manual and Computer Lead for Power Connection.

Optional: Trainer Kit Available in Digital Meters and Round Meters

Additional Information:

• Item Code: UNICON-D236

Z AND Y PARAMETERS OF TWOPORT NETWORK TRAINER

FEATURES:

Instrument comprises of  DC IC Regulated Power Supplies 0-15V/150mA.

On Board Ac Supply 15V.

Two MR65 Square / Digital / Round meters for voltage & current measurement.

T and PIE Network provided on the board.

Variable Resistor Using Band switch is mounted on the board.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 12’’x8’’

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D235

UJT CHARACTERISTICS TRAINER

OBJECTIVE:  To plot Static & Transfer Characteristics. 

FEATURES:

Instrument comprises of Two DC IC Regulated Power Supplies 0-15VDC/150mA & 0- 30VDC/150mA.

Three MR65 Square/Digital meters for voltage & current measurement.

One UJT 2N2646 mounted behind the panel.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 12’’x8’’ 

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D234

TWO PORT LADDER TRAINER

FEATURES:

Instrument comprises of  DC IC Regulated Power Supplies 0-20V/150mA.

On Board AC Supply 15V

Two MR65 Square/Digital/Round meters for voltage & current measurement.

T and PIE Network Provided on the board.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 10’’x8’’

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D233

TRIAC CHARACTERISTICS TRAINER

OBJECTIVE:  To plot Static & Transfer Characteristics. 

FEATURES:

Ø     Instrument comprises of Two DC IC Regulated Power Supplies 0-5VDC/150mA & 0- 30VDC/150mA.

Ø     Three MR65 Square/Digital meters for voltage & current measurement.

Ø     One BT136 mounted behind the panel.

Ø     Instrument Fitted in Highly Shockproof Plastics Box.

Ø     Instrument Dimensions: 12’’x8

ACCESSORIES:

Ø     Sufficient no of 4mm Patch Cords for Interconnection

Ø     Instruction Manual for Student Workbook.

Ø     Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D232

T AND PIE TYPE ATTENUATOR TRAINER

FEATURES:

Instrument comprises of  DC IC Regulated Power Supplies 0-15V/150mA.

Two MR65 Square / Digital / Round meters for voltage & current measurement.

T and PIE Network provided on the board.

Variable Resistor Using Band switch is mounted on the board.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 12’’x8’’

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D230

TRANSISTOR CHARACTERISTICS (NPN/PNP) TRAINER

Ø     Trainer used to study characteristics of Transistor of NPN/PNP in Common Emitter, Common Base,

Ø     Kit comprises of 4 Digital meters voltmeter 1V, 10V and ammeter of 250uA/50mA. 50mA.Built in regulated power supplies 0-1V& 10V required characteristics in different mode.

Ø     Meter ranges are selectable with toggle switches

Ø     2 transistor NPN/PNP connected and their terminals are brought on front panel for easy connections via 4m sockets.

Ø     Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.

Ø     Supplied with instruction manual.

Ø     Operated on Mains power 230V, 50Hz.

Ø     Supplied with sufficient nos. of patch cords  & power inlet cable

Ø     Supply provided through the 3 pin computer socket with appropriate fuse

Ø     The trainer is housed in plastic cabinet to avoid shock

Ø     Size of the trainer set 15”x8” 

Additional Information:

• Item Code: UNICON-D231

SCR CHARACTERISTICS TRAINER

OBJECTIVE:  To plot Static & Transfer Characteristics. 

FEATURES:

Instrument comprises of Two DC IC Regulated Power Supplies 0-5VDC/150mA & 0- 30VDC/150mA.

Three MR65 Square/Digital meters for voltage & current measurement.

One TYN604 mounted behind the panel.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 12’’x8’’

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D229

SERIES AND PARALLEL RESONANCE TRAINER

Optional: Trainer Kit Available with Audio Oscillator or Audio Function Generator.

The offered range is known for studying the series and parallel resonance in LCR circuits, measurement of q. Along with this, the offered range is widely applicable for different science and engineering fields.

Special Feature:

1.     inductances made on ferrite cores, selectable by a switch.

2.     capacitances with low loss factor, selectable by a switch

3.     resistances, selectable by a switch

4.     Adequate no. of patch cords stackable from rear both ends 4/ 2mm spring loaded plug length ½ meter

5.     Good quality, reliable terminal/sockets are provided at appropriate places on panel for connections/ observation of waveforms

6.     Strongly supported by detailed operating instructions manual.

Additional Information:

• Item Code: UNICON-D228

PN JUNCTION DIODE CHARATERISTICS TRAINER 4 METERS 

• Kit comprises of 4 Meters Voltmeter 3V and30 and Ammeter of 100uA and10mA.
• Built in regulated power supply 0-3V and 30V required for forward and reverse characteristics.
• PN Diode connected on the panel via 4mm sockets.
• Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.
• Operated on Mains power 230V, 50Hz.
• Accessories: Required numbers of Patch Cords, Operating Manual and Computer Lead for Power Connection.

Optional: Trainer Kit Available in Digital Meters and Round Meters

Additional Information:

• Item Code: UNICON-D227

PN JUNCTION DIODE CHARATERISTICS TRAINER

• Kit comprises of 2 Meters Digital Type Voltmeter 3V/30 and Ammeter of 100uA/10mA.
• Built in regulated power supply 0-3V/30V required for forward and reverse characteristics.
• PN Diode connected on the panel via 4mm sockets.
• Front plate built with high class insulated Bakelite sheet with well printed circuits and symbols.
• Operated on Mains power 230V, 50Hz.
• Accessories: Required numbers of Patch Cords, Operating Manual and Computer Lead for Power Connection.

Optional: Trainer Kit Available in Digital Meters and Round Meters

Additional Information:

• Item Code: UNICON-D226

MOSFET CHARACTERISTICS TRAINER

OBJECTIVE:  To plot Static & Transfer Characteristics. 

FEATURES:

Instrument comprises of Two DC IC Regulated Power Supplies 0-5VDC/150mA & 0- 20VDC/150mA.

Three MR65 Square/Digital meters for voltage & current measurement.

One MOSFET IRF540 mounted behind the panel.

Instrument Fitted in Highly Shockproof Plastics Box.

Instrument Dimensions: 12’’x8’’

ACCESSORIES:

Sufficient no of 4mm Patch Cords for Interconnection

Instruction Manual for Student Workbook.

Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D225

LOWPASS AND HIGHPASS FILTER TRAINER USING RC-LC

FEATURES:

·        Instrument Comprises Low Pass Circuit RC Type.

·        Instrument Comprises Low Pass Circuit LC Type.

·        Instrument Comprises High Pass Circuit RC Type.

·        Instrument Comprises High Pass Circuit LC Type.

·        Instrument Fitted in Highly Shockproof Plastics Box.

·        Instrument Dimensions: 12’’x8’’

ACCESSORIES:

·        Sufficient no of 4mm Patch Cords for Interconnection

·        Instruction Manual for Student Workbook.

Additional Information:

• Item Code: UNICON-D224

KCL-KVL TRAINER

OBJECTIVE:  Verification of Kirchhoff’s Voltage and Current Law.
FEATURES:

·        Instrument comprises of Two DC IC Regulated Power Supplies 0-12V/150mA.

·        Two MR65 Square/Digital meters for voltage & current measurement.

·        Components are mounted behind the panel with printed circuit diagram.

·        Connections are brought with 4mm banana sockets.

·        Instrument Fitted in Highly Shockproof Plastics Box.

·        4mm patch cords are provided with the trainer for interconnections.

·        Student work book will be provided with the trainer kit,

·        Instrument Dimensions: 10’’x8’’

·        Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D223

HALF WAVE, FULL WAVE & BRIDGE RECTIFIER

OBJECTIVE: To study Efficiency & Ripple factor in case of half wave, Full wave & Bridge rectifier on application of load & filters.
Specifications:

·          Instrument comprises inbuilt  AC Power Supply 15-0-15V

·          2 meters Square MR65 to measure Output Voltage & Output current

·          4 PN Junction Diodes

·          Filter Circuit Kit With Switch Selectable.

·          Inbuilt inductor having value of 200mH on board.

·          Load Resistance.

Features

·          Trainer operated on 230V, 50 Hz + 10%

·          Supplied with instruction manual

·          Supplied with sufficient nos. of patch cords

·          Supplied with Computer Lead

·          Dimensions of the Trainer will be 12’’x8’’ with Plastic Box Highly shock proof . 

Additional Information:

• Item Code: UNICON-D222

4-BIT PARITY GENERATER AND CHECKER TRAINER

OBJECTIVE: To Generating and checking of Parity Bit

FEATURES :

· Instrument comprises of DC Regulated Power Supply 5VDC/150Ma.

· 5 SPDT switches provided for selecting logic ‘1’ & logic ‘0’.

· 2 output indicators.

· Circuit diagram for Parity Generator and Parity Checker is Printed.

· Instrument Fitted in Highly Shockproof Plastics Box.

· Instrument Size: 12’’x8’’

· ACCESSORIES:

· Sufficient no of 4mm Patch Cords for Interconnection

· Instruction Manual for Student Workbook.

· Power Cords 230v, 50Hz

Additional Information:

• Item Code: UNICON-D242