V-Care Electronics

This low cost unit monitors speed (RPM) from a proximity sensor and it gives out a potential free relay output if the input RPM is above or below the set speed. This product finds its use in various applications. One such application is Belt breakage monitoring...read more...

The DAC module takes digital inputs from PLC/NC and gives out a corresponding control analog output. The inputs are 24V level (Sourcing/Sinking) and are optically isolated. An analog output of 0-10V is available corresponding to the 12 bit digital inputs.

Additional Information:

• Item Code: DAC12

v-care make isolation transducer takes dc voltage/ dc current and provides stable, optically isolated dc output in the form of current.   isolation amplifiers are used as analog interfaces between systems with separated grounds. The output can be connected to plc’s, analog /digital indicators, data-logging instruments or control. These are ideal for supervisory control and data acquisition (scada) and central monitoring systems.      
 
products in this catagory includes following isolated converters     isotransd
       
      voltage to current converters
      current to voltage converters
      current to current converters
      voltage to voltage convert

Diode cards are used to drive 24V LED’s directly and lamps on a mimic panel and operator panel. It is a PCB with the diodes required for the two inputs and LAMP TEST (see the circuit diagram) assembled on a compact PCB which can be mounted on DIN RAIL.

Diode card with lamp test boards are used to drive LED’s and lamps on a mimic panel and operator panel. It is a PCB with the components like resistor for limiting the current through the LED and the diodes required for the LAMP TEST (see the circuit diagram) assembled on a compact PCB which can be mounted on DIN RAIL.

Additional Information:

• Item Code: DC-08LD

Additional Information:

• Item Code: DISO_322424

Additional Information:

• Item Code: DISO_162424

this microcontroller based caternary voltage monitoring relay is used to monitor the line voltage and give a control output whenever the line voltage falls below the set level with hysterisis. The unit is powered by auxiliary power 24v dc. The sense voltage is measured and displayed on the 4 digit display. . . . . Read more. . .

V-CARE’s TAP POSITION INDICATOR is used to indicate the tap position of the power transformer with On-Load Tap-Changer (OLTC). The step resistance is connected between each tap position at the transformer end. The minimum, maximum and wiper (common) connections are brought to the Tap position Indicator..read more..

V-care introduces its latest micro-controller based panel meters. These panel meters are used to indicate different parameters such as current, voltage, rpm, pressure, flow, load etc. The panel meters accept 0-10Vdc, 0-5Vdc, 2-10Vdc, 1-5Vdc or 0-20mA/4-20mA and will have 4 digit display or 5 digit display depending on the model. These models are available with AC Power input (230Vac) or DC power input (15 – 24Vdc) and these are housed inside a half DIN enclosure...read more.....

This unit operates from 24V DC power. The timer starts when the ENABLE SIGNAL is given to the unit. The relay is initially de-energized. When actual time exceeds the set time control relay is energized....read more...Models with UP TIMER, DOWN TIMER, UP/DOWN counters are available...

these are functionally similiar to the above mentioned product, provided that the unit gets the input from ac drives in the form of current i. E. 0-20ma or 4-20ma. The unit operates from 24v dc power and takes 0-20ma/4-20ma input. Provision to set various control parameters like start-up delay, trip-off delay. . . Read more. . . . this product is available with voltage input and pulse input. . . . .

Additional Information:

• Item Code: DISO_-16LD

This is the latest of our Power monitors designed to monitor the load on tool without any external sensors mounted on the tool, in induction motor driven applications. The load is measured indirectly by measuring the input power to the motor. The power drawn by the motor increases with increase in load on the tool. There will be a substantial increase in the input power during accident condition like tool breakage or jamming. This condition can be sensed and the motor can be tripped, avoiding further accidents..read more

Additional Information:

• Item Code: DISO_1611024

Additional Information:

• Item Code: DISO__4524

This level translator takes active high input (sourcing) type input and gives an active low (sinking) open collector output or sourcing outputs. It draws minimum current from the input and gives comparatively high sinking currents (150mA). Four such drivers are provided in a module and a free wheeling diode is also provided to the output common from each output. This is useful for driving inductive loads. A zener is provided in series with each input. This ensures a 'must cross' voltage for inputs which enhances the noise immunity of the unit.

Additional Information:

• Item Code: LVT524

Rail mounted relay interface modules for input and output interface of plc, for electrical isolation of plc from the input and output signal. This portion of the catalogue mentions standard and custom made interface modules. The interface inputs are designed for dc drives. The switching status is indicated via an led. Some of the features include replaceable fuse and easy to replace pluggable relays, possibility of bussing of relays in common negative or common positive configurations, minimum possible size etc. , view catalog

Additional Information:

• Item Code: 24-4-DFUP

These Diode cards are used to OR two types of digital inputs. These cards accepts two seperate inputs and gives out one.

Additional Information:

• Item Code: DC-01AM

We offer high quality high profile led/lamp control board with lamp test

Additional Information:

• Item Code: DC-16LM

The URD2 controller unit which is also called as Temperature controller controls all the functions of the dryer, allowing also the calibration of all the parameters. A probe located at the end of the evaporator pilots the activation of the hot gas bypass solenoid valve....read more...

Panel meters / signal sources / simulation units -  current source

These current sources are ideal for applications where constant current is required. These sources finds their use for simulation of analog current to test analog cards/rtu's/plc's. Current can be set between 0-20ma with 0. 01ma resolution. The current output can be adjusted usnig front panel keys.

this microcontroller based dc low voltage cutoff unit is used to monitor the line dc voltage (110vdc) and give a control output whenever the line voltage falls below the set level i. E. 103vdc with hysterisis. . . . . Read more. . .

Additional Information:

• Item Code: RM114

Additional Information:

• Item Code: RM104HL

Additional Information:

• Item Code: RM104

Additional Information:

• Item Code: RM128

Additional Information:

• Item Code: RM124

Additional Information:

• Item Code: RM108

Additional Information:

• Item Code: RM101

Additional Information:

• Item Code: RM108HL